background image

Installing the Unit

1. Using the foam adhesive backer of the remote as

a template, determine the mounting location on

the mounting surface and mark the three hole

locations. 

2. Remove the foam adhesive backer and drill two

3/8" and one 5/8" mounting holes in the marked

positions.

3. Remove the backer to the foam adhesive backer

and adhere it to the back of the remote. 

4. Feed the remote wire through the 5/8" hole in the

mounting surface and attach the remote to the

mounting surface using the supplied screws. 

5. Attach the remote wire to the unit according to

the wiring diagram on Page 11. 

Note: The Wired Remote comes with an extension

cord so the remote can be mounted a far distance

from the receiver. 

This unit is a wired remote control made using a modified controller or similar layout. It is capable of

operating the specified functions on the M5100CD receiver. The body, buttons, controls and display are

UV and water-resistant. It includes a LCD and an illumination circuit.

Take a moment to read through this section and become familiar with the operations and features of this

outstanding product. It is advisable to keep this manual in your vehicle so it is readily available for refer-

ence. Be sure to fill out and send in your warranty card to ensure that you receive the full benefits of war-

ranty repair in the unlikely event that your system will need service.

Waterproof Wired Remote Introduction

Installation Procedures

8

Mounting Surface

Foam Adhesive 
Backer

Mounting Surface

Mark & Drill Holes

Screws

Wire to Unit

Mounting Surface

M5100CDUMFinal  2/1/05  4:58 PM  Page 8

Summary of Contents for M5100CD
















Reviews: