Magma P10-501 Owner'S Manual Download Page 7

6

OPERATING PROCEDURES

WARNING:

Do not overheat grill. Magma grills do not require pre-heating. Stainless

Steel loses anti-corrosive characteristics when subjected to extreme heat. Most grilling is
done on low temperature with the lid closed. If medium or high heat is required, grill
with lid open. 

LIGHTING INSTRUCTIONS

• Open lid during lighting, hang lid on side of the grill to block the wind (see 14).
• When igniting grill, use a long nozzle butane lighter.
• To ignite grill, first ignite lighter or match flame, put flame to outer edge of Radiant

Plate, then turn valve to high "large    ".

• To grill, cook with lid on.

To help create your own Magma gourmet experience every time you grill,

please check these important critical points prior to lighting your grill.

• Mount is secure and grill does not move.
• Grease tray and fire pan are clean from excess drippings to reduce flare up and

ensure even air flow.

• Lid is correctly positioned to operate freely and is in best position for blocking the

wind.

• Venturi tube, burner, threaded burner pipe and valve orifice are free of obstructions,

such as spider webs.

• Radiant plate is positioned correctly.
• Grill grate is in locked position under holding clips.
• Turbo Venturi Tube holding nut is tight & doesn't turn when rotating valve position.
• Valve is installed and locked into Turbo Venturi Tube properly.
• Sufficient fuel is available.

Cooking Tips

• The most common mistake when grilling is using too high of a heat setting. Grills

become hotter as you cook, so use moderate heat settings when cooking with lid
closed. 

• Always keep a water spray bottle handy for flare ups and quick cooling if grill

overheats.

• Coat the grill grate with vegetable or olive oil to prevent food from sticking. 

Stowing Tips

• Always disconnect the fuel canister from the valve prior to stowing. 
• Stow the valve and Turbo Venturi Tube in a clean, dry area to protect from

corrosion to valve and spider web obstructions in venturi tube.

• Always stow by unthreading the entire grill from the L-Bracket. Do not remove the

L-Bracket & Clamp unless repositioning is necessary. 

• Always store propane in a sealed propane storage locker that allows leakage to

vent overboard or use 

Magma A10-210 Propane Storage Tote

. Never stow

below  decks.

Summary of Contents for P10-501












Reviews: