background image

OPERATING PROCEDURES

WARNING: Do not overheat grill. Magma grills do not require pre-heating. Stainless Steel loses anti-corrosive 

characteristics when subjected to extreme heat. Most grilling is done on low temperature with the lid closed.  

If medium or high heat is required, grill with lid open. 

LIGHTING INSTRUCTIONS

• Open lid during lighting. • Depress knob & rotate counter-clockwise to the “HIGH” position. 
• Push Electronic Pulse Igniter.  • Visually confirm ignition.  • Turn knob to adjust flame.
• If grill does not light, insure that a burner electrode spark cap is directly above electrode.
• If the Electronic Pulse Igniter continues to fail to ignite the gas, see MATCH LIGHTING INSTRUCTIONS. 
NOTE:  Electronic ignition comes equipped with battery preinstalled. Replace with “AAA” alkaline battery only.

To help create your own Magma gourmet experience every time you grill,  

please check these important critical points prior to lighting your grill.

• Mount is secure and grill does not move.  • Electrode is clean and electronic ignition creates a spark.
• Grease tray and fire pan are clean from excess drippings to reduce flare up and  ensure even air flow.  
• Lid is correctly positioned to operate freely and is in best position for blocking the wind.
• Venturi tube, burner, threaded burner pipe and valve orifice are free of obstructions, such as spider webs. 
• Radiant plate is positioned correctly.  • Grill grate is in locked position under holding clips.  
• Turbo Venturi Tube holding nut is tight & doesn't turn when rotating valve position.  
• Valve is installed and locked into Turbo Venturi Tube properly.  • Sufficient fuel is available.

Cooking Tips

• The most common mistake when grilling is using too high of a heat setting. Grills become hotter as you cook, 

so use moderate heat settings when cooking with lid closed.   

• Always keep a water spray bottle handy for flare ups and quick cooling if grill overheats.  
• Coat the grill grate with vegetable or olive oil to prevent food from sticking.

Stowing Tips

• Always disconnect the fuel canister from the valve prior to stowing. 
• Stow the valve and Turbo Venturi Tube in a clean, dry area to protect from corrosion to valve and spider web 

obstructions in venturi tube.

• Always stow by unthreading the entire grill from the L-Bracket. Do not remove the L-Bracket & Clamp unless 

repositioning is necessary. 

• Always store propane in a sealed propane storage locker that allows leakage to vent overboard or use Magma 

A10-210 Propane Storage Tote. Never stow below decks.

7

MATCH LIGHTING INSTRUCTIONS

(Back up system allows use of grill until Electronic Pulse Igniter system is repaired.)

• Open lid during lighting.
• Place flame up to burner through the match light hole.
• Depress valve and turn counter-clockwise to the “High” position.   
• Visually confirm ignition.

Match Light Hole

TO REDUCE FLARE-UP

• Trim excess fats from meat.         • Reduce heat.
• Use non-oil based marinades.      • Use water spray directly on flare-ups.

Summary of Contents for MARINE KETTLE A10-207-3













Reviews: