background image

have problems with the USB connection, please refer to the 
Installation Guide for details on how to install the proper driver. 

When connecting the unit via an Ethernet network, you have several 
options. The PC/MAC application has an auto-discovery tool that will 
automatically connect to any unit found on the network. 

Standard DHCP Network 

For the easiest connection, use a standard Ethernet Router, plug in 
the unit and your computer, and the connection should be made 
automatically. Standard routers have a DHCP server built in and 
enabled. A DHCP server assigns a network address to your computer 
and to the DSP, allowing them to connect automatically. 

!

Connection without DHCP server 

Alternatively, you can use a direct (cross) cable or a simple Ethernet 
Switch to connect the unit to your PC or MAC. Please note that in 
this case, especially Windows computers may take up to several 
minutes to assign themselves a network address (indicated by the 
text: "This connection has limited or no connectivity"). The computer 
and the DSP both will assign themselves a network address in the 
ZeroConfig range (169.254.0.0 - 169.254.255.255), and the DSP 
will be discovered automatically by the PC/MAC application. 

To facilitate connections without DHCP router, it may be convenient 
to set your computer to a fixed IP address. If you do this, please 
choose any address in the ZeroConfig range, and set the subnet 
mask to 255.255.0.0. 

Fixed IP address 

It is also possible to set a fixed IP address and subnet mask for the 
1800B. WARNING: If you set a wrong address (in a different range 
than your computer), you may not be able to connect anymore. It is 
STRONGLY RECOMMENDED to consult a system administrator before 
making such settings. 

Firewall 

After starting the software application for the first time, your 
computer may ask you to allow or block the application access to the 
network. Please make sure to allow this; if there is a firewall 
between the application and the DSP the application will not find the 
DSP. 

!

System Setup and Gain Structure 

!

 of 

!

15

21

Summary of Contents for Q-Sub






















Reviews: