background image

 

 

 

-25- 

MAFELL,  with  the  machine  having  to  rest  on  the 
workpiece with its base plate 3 (Fig. 1). The machine 
may  be  operated  by  one  person  only.  At  the  same 
time, the machine must be held and guided by its two 
handles 1 and 2 provided for that purpose. 

  

Any  other  use  than  described  above  is  not 
permissible.  The  manufacturer  cannot  be  held  liable 
for any damage arising from such other use. 
So  as  to  use  the  machine  as  intended,  comply  with 
the  operating,  maintenance  and  repair  instructions 
specified by Mafell. 

  

2.8

 

Residual risks 

 

Danger 

Even if used in accordance with its 
intended purpose and despite 
conforming with the safety 
instructions, residual risks caused 
by the intended use that can lead 
to health consequences will always 
remain. 

  

Touching  the  running  saw  chain  below  the  base 
plate. 

Touching  the  standing  saw  chain  below  the  base 
plate. 

Machine  backlash  if  the  blade  gets  stuck  in  the 
workpiece. 

Tearing of the saw chain. 

Ejection of timber cuttings. 

  

Touching live parts with the housing open and the 
mains plug not removed. 

Hearing  can  be  impaired  when  working  for  long 
periods without ear protectors. 

Emission  of  harmful  wood  dusts  during  longer 
operation without extraction. 

  

3

 

Safety instructions 

 

Danger 

Always observe the following safety 
instructions and the safety 
regulations applicable in the 
respective country of use! 

  

General instructions: 

Children  and  adolescents  must  not  operate  this 
machine.  This  rule  does  not  apply  to  young 
persons receiving training and being supervised by 
an expert. 

Never  work  without  the  protection  devices 
prescribed  for  the  respective  operating  sequence 
and do not make any changes to the machine that 
could impair safety. 

When  operating  the  machine  outdoors,  use  of  an 
earth-leakage circuit-breaker is recommended. 

Do not carry the machine by its cable and do not 
use  the  cable  to  pull  the  plug  out  of  the  socket 
outlet. 

Pay attention that the cable is protected against oil 
and heat and is not pulled across sharp edges. 

Damaged  cables  or  plugs  must  be  immediately 
replaced. Replacement may only be carried out by 
Mafell or an authorised MAFELL service workshop 
in order to avoid safety hazards. 

Avoid  sharp  bends  in  the  cable.  Especially  when 
transporting and storing the machine, do not wind 
the cable around the machine. 

  

Always check before beginning work, whether the 
protection  and  work  equipment  is  safely  attached 
and  not  damaged.  Damaged  protection  devices 
and  parts  must  be  repaired  or  replaced 
appropriately. 

Consider environmental influences. Do not expose 
the machine to rain and  avoid working in a damp 
or wet environment as well as near to combustible 
liquids or gases. 

Store the device in a dry, locked place outside the 
reach of children. 

  

Instructions  on  the  use  of  personal  protective 
equipment: 

Always wear ear protectors during work. 

Always where a dust mark during work. 

  

Always wear closely fitting work clothes (no shorts) 
and take off rings, wristbands, and watches. 

  

Instructions on operation: 

  

Provide for an unobstructed and slip-proof location 
with adequate lighting. 

  

Summary of Contents for ZSX Ec



















Reviews: