Maeda MC-174CRM Quick Operation Manual Download Page 9 | Manualshive

Page: 9 / 11

Maeda MC-174CRM Quick Operation Manual Download Page 9

8.1 PROCEDURE IN THE OPERATION MODE

[1] CALL UP CRANE MODE

1. Push the Power button to turn ON the Transmitter.

2. The “Crane mark” is displayed in the LCD screen for about 2 seconds.

3. The crane is ready for operation.

[2] CALL UP OUTRIGGER MODE

1. Push the Power button to turn ON the Transmitter.

2. The “Crane mark” is displayed in the LCD screen for about 2 seconds.

3. While the “Crane mark” is displayed, push the speed button for about 2 seconds. The LCD provides the screen for

selecting “CRANE MODE” or “OUTRIGGER MODE”.

4. Use the Hook raising and lowering Lever to shift the cursor ( or ), and push the Setting button when the cursor

points to the “OUTRIGGER”, then the “outrigger mark” is exhibited.

5. Soon after, it enters into “Outrigger collective setting mode (ALL)” automatically, then the mark turns to “Outrigger

collective setting mode (ALL) .

6. To shift to “Outrigger individual setting mode”, push the Speed/Mode button, while the LCD screen shows the

“Outrigger collective setting mode (ALL)”. Then the mode is switched to “outrigger individual setting mode”; the

mark turns to “Outrigger individual setting mode (

)”.

9

«
...
7
8
9
10
11
»

Summary of Contents for MC-174CRM












Reviews:

No comments