background image

MDB S

eries Dir

ect Bo

xes

8

MDB Series Direct Boxes

MDB Series DIrect Boxes: Front Panel Features

1. Input Jacks

The signal output from an instrument (active  

or passive) may be connected to this unbalanced 

line-level 1/4” input by means of a shielded instrument 

cable. This includes guitar, bass, keyboard, media  

players and more.

They are wired as follows, according to standards 

specified by the AES (Audio Engineering Society): 

Unbalanced 1/4" Input Connector
 

Tip – Positive (+ or hot) 

 

Sleeve – Shield (ground)

NEVER connect the output of an amplifier 

directly to an MDB Series Direct Box’s input 

jack. This could damage the input circuitry 

and we wouldn’t want that now, would we?

2. Thru Jacks

The Thru jack may be connected to the input  

of an instrument amplifier or instrument-level  

parallel effects device (such as an FX device chain, 

processors, or tuner). This output is unaffected  

by the MDB Series Direct Box’s circuitry.

SLEEVE

TIP

TIP

SLEEVE

TIP

SLEEVE

Unbalanced 1/4" Connectors

PAD

PAD

0 dB

-15 dB

0 dB

-15 dB

THRU

INPUT

LEFT

RIGHT

MDB-2P Front Panel

1

2

3

3

3. Pad Switch

Put this switch in the down position to reduce  

the input signal by 15 dB and compensate for higher 

output sources. This attenuation is suited for use with 

instruments that have active electronics or high-output 

pickups.

It is a 20 dB pad on the MDB-1A and the 

switch is reversed from the MDB-1P and 

MDB-2P; –20 dB in the up position, 0 dB 

when the switch is down.

4. Merge Switch [MDB-1A]

When the Merge switch is in the OFF position  

(switch up), the Thru jack works as normal  

(see #2 description, bottom-left).

When the Merge switch is in the ON position (switch 

down), the Thru jack works as an additional input.  

It will be summed with the main input to create a mono 

output source. This is a perfect solution for stereo 

sources like keyboards and media players.

Additionally, the associated LED will illuminate  

when merge is on.

MBS On / Off Switches

The rare and highly sought after MBS–FNMA and 

MBS–GNMA Direct Boxes come with switches to turn 

off your mind, body and soul when any (or all) of them 

need it. When will you know? Oh, you’ll know. When it’s 

there, simply flip the switch to off and when you’re 

feeling good again, go ahead and flip the switch back 

to the on (up) position.

INPUT

MERGE

PAD

THRU

ON

OFF

0 dB

-20 dB

POWER

MDB-1A Front Panel

1

2

3

4

INPUT

PAD

0 dB

-15 dB

THRU

MIND

ON

OFF

BODY

ON

OFF

SOUL

ON

OFF

MBS-FNMA & GNMA 

INPUT

PAD

0 dB

-15 dB

THRU

MDB-1P Front Panel

1

2

3

Summary of Contents for MDB-1A
















Reviews: