background image

DL1608

DL1608

14

 

Channel Strips: FX and iPad

  Drag the 

Mixer View

 left until 

Channel Strips 12 – 16, Reverb, 
Delay, iPad and the Master Fader are 
in view. The two FX channels [Reverb 
and Delay] and one iPad channel 
look similar to Channel Strips 1 – 16, 
but function a little differently. Let’s 
find out how...

Channel Strips: Reverb / Delay

  There are three ways in which 
the Reverb and Delay channel strips 
differ from the other channel strips. 

  First, the Pan slider becomes  
a Balance slider, acting as a stereo 
balance. It allows you to adjust  
how much of the left or right  
output signals are heard. Touch  
and drag the slider left or right    
to make adjustments.

  Also, there are no dynamics on  
FX channels, so Gain Reduction 
Meters are not shown. 

  Finally, since these are stereo 
returns, the meters are in stereo, 
not mono.

  You will learn how to adjust    
the FX soon.

Channel Strips

Channel Strips 

12 – 16

iPad

Master 

Fader

Delay

Reverb

Channel Strips: iPad / Playback

  This is the channel where you 
control the level and EQ from the 
iPad music library or any other 
audio app on the iPad that supports 
background audio playback. 

  Keep the iPad attached to the 
mixer here, as playback only works 
when attached to the DL1608,  

 

not in Wi-Fi mode.

  Now start playback in the audio 
app of your choice, then switch to 
the Master Fader app to control that 
source in the mix.

Summary of Contents for DL1608

































Reviews: