background image

Safety Instructions

Read these safety instructions thoroughly and follow all the instructions.

1.

Only an operator who is fully authorized to drive a tractor can operate the
MachineryGuide AutoSteer system. It is not allowed under any conditions for
an unauthorized person to operate the MachineryGuide AutoSteer system.

2.

The operator must have sufficient knowledge of procedures on how to
operate the MachineryGuide AutoSteer system before starting to operate it.

3.

Only an operator who is trained or is experienced must operate the
MachineryGuide AutoSteer system. Always operate the system in a safe
manner.

4.

If there are any questions regarding the operation of the MachineryGuide
AutoSteer system do not hesitate to contact the responsible expert or the
MachineryGuide team.

5.

The operator must always be conscious of their actions while operating the
MachineryGuide AutoSteer system.

6.

The operator must not exceed the maximum speed limit for the actual terrain
the vehicle is operated.

7.

Only use the MachineryGuide AutoSteer system in appropriate weather and
terrain conditions. Do not use the MachineryGuide AutoSteer system in low
visibility.

8.

Always follow the instructions in the installation and operation manual.

9.

While installing the parts of the MachineryGuide AutoSteer system do not
force components to avoid damage or failure of them.

10. Only authorized parties should install the MachineryGuide AutoSteer system.

11. Carry out an inventory of the components delivered before starting to install

the MachineryGuide AutoSteer system to make sure all components are
present. Do not use replacement components if not stated otherwise.

12. Always use the correct tools to install the MachineryGuide AutoSteer system.

13. Be careful while installing the MachineryGuide AutoSteer system to prevent

any injury or damage to property.

14. While installing and operating the MachineryGuide AutoSteer system all

safety precautions must be taken into account and it should not be used if
any parts are loose, damaged or missing. Before starting a vehicle with

3

Summary of Contents for AutoSteer























Reviews: