background image

ELEVATION AXIS OPTION #1 

 

Characteristics 

Spectrum of use: 0° to 90° plus 

Over travel amount: 10°  

SU Designation: Elevation 90° 

 

OVERVIEW:  

 

This Elevation configuration is used as standard 

throughout the industry and may be used when 

0° to 90° of travel is necessary. Note the position 

of the Physical limit switches, they are on the 

outside of the electrical limits. Ultimately this   

provides safety when and if a control box may 

fail.  

VIEWED FROM THE 

SIDE OF THE  

SYSTEM  

UP PHYSICAL LIMIT .105° 

DWN ELECTRICAL LIMIT –.5° 

DWN PHYSICAL LIMIT –.10° 

UP ELECTRICAL LIMIT .100° 

ELEVATION AXIS OPTION #1 

 

Characteristics 

Spectrum of use: 0° to 180° plus 

Over travel amount: 10°  

SU Designation: Elevation 180° 

 

OVERVIEW:  

 

This Elevation configuration is used as standard 

throughout the industry and may be used when 

0° to 180° of travel is necessary. Note the        

position of the Physical limit switches, they are 

on the outside of the electrical limits. Ultimately 

this provides safety when and if a control box 

may fail. 

 

 

*Note due to your dish or antenna size, there 

may be limitations of the overall range above 

125°. 

HORIZON 

HORIZON 

DWN ELECTRICAL LIMIT –.5° 

DWN PHYSICAL LIMIT –.10° 

VIEWED FROM THE 

SIDE OF THE  

SYSTEM  

UP ELECTRICAL LIMIT .180° 

UP PHYSICAL LIMIT .185° 

ELEVATION SYSTEM CONFIGURATION 

Summary of Contents for RC2800PRKX1SU

























Reviews: