background image

Self  Charging Battery Back-up

The special NiCad 2.4v self-charging battery recharges continuously during train 
operation and  should last for up to five years.  The battery is a dry battery that 
should not leak or cause any damage to your engine.  Depending upon when your 
engine was built, it may need to be charged right out of  the box.  If  engine sounds 
seem distorted or garbled at low voltages or become silent when power from the 
transformer is turned off, test the battery to determine whether it should be 
recharged or replaced.

Test:

  Put the engine in neutral and                                                                    

leave the track voltage at 10-12 volts                                                                   
(high enough for the lights to shine                                                                   
brightly) for 15 minutes.

Recharge:

  If  the sounds are improved                                                                  

at the end of  the 15-minute test charge,                                                                 
the battery charge has run down and can                                                               
be recharged.  There are a number of                                                                         
ways you can do this:

• Leave the engine in neutral with track voltage at 10-12 volts                                       
   for 6-7 hours so the battery can fully recharge (if  your engine has a 
    smoke unit, be sure it is turned off).

•Use M.T.H.'s battery recharger (sold separately) that plugs into a wall 
outlet and a special port under the engine to recharge the battery 
overnight without leaving it on the track.

Replace:

  If  the sounds are not improved at the end of  the 15-minute test charge, 

it is time to replace the battery.  Available through M.T.H. Parts.  

Premier GP40  Diesel Engine Proto-Sound®2.0

15

Battery Charger Port

Disconnect Battery And Slide Out Of Bracket

Figure 9. Battery Char ger Port location.

Figure 10. Battery Location.

Summary of Contents for Premier GP40 Diesel Engine
























Reviews: