background image

R7M-DAC16C

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: [email protected]

EM-7803-AK  Rev.4  P. 3 / 8

 

POWER SUPPLY, MODBUS TERMINAL ASSIGNMENT

4

DA

5

6

7

1

2

3

DG +24V

0V

DB

SLD

FG

(1)  DB 

(2)  SLD 

Shield

(3)  FG 

FG

(4)  DA 

(5)  DG 

(6)  +24V 

Power input (24V DC)

(7)  0V 

Power input (0V)

 

I/O TERMINAL ASSIGNMENT

14

5

6

X7

X6

Y0

15

Y1

16

17

18

7

8

9

Y3

Y5

Y7

Y2

Y4

10

1

2

C+

C–

X0

11

X1

12

13

3

4

X3

X5

X2

X4

Y6

NO.

ID

FUNCTION

NO.

ID

FUNCTION

1

C–

Common–

10

C+

2

X0

Input 0

11

X1

Input 1

3

X2

Input 2

12

X3

Input 3

4

X4

Input 4

13

X5

Input 5

5

X6

Input 6

14

X7

Input 7

6

Y0

Output 0

15

Y1

Output 1

7

Y2

Output 2

16

Y3

Output 3

8

Y4

Output 4

17

Y5

Output 5

9

Y6

Output 6

18

Y7

Output 7

 

TERMINATING RESISTOR

To use the terminating resistor, turn the switch ON, and 
OFF to invalidate. 
(Factory setting: OFF)

 

EXTENSION MODULE

Combinations with all extension modules are available.

PC CONFIGURATOR

With configurator software, settings shown below are available.
Refer to the software manual of R7CON for detailed operation.

 

INTERFACE MODULE SETTING 

PARAMETER

AVAILABLE RANGE

DEFAULT SETTING

Communication Timeout

0.0 – 3276.7 (sec.)

1.0 (sec.) 

Data Mode

RTU / ASCII

RTU

Parity

NONE / ODD / EVEN

NONE

 

CHANNEL INDIVIDUAL SETTING

PARAMETER

AVAILABLE RANGE

DEFAULT SETTING

Output Operation Mode

Maintained / Momentary

----

Summary of Contents for R7M-DAC16C









Reviews: