background image

MINI-TOP ELECTRONIC ACTUATOR

(linear type; CC-Link)

MODEL

MSP4C/MSP5C

/MSP6C

CONTENTS

1.  BEFORE USE .... ...................................................................................................... 2

2.  POINTS OF CAUTION ................................................................................................. 2

3.  COMPONENT IDENTIFICATION ..................................................................................... 3

4.  OUTPUT SPAN ADJUSTABILITY .................................................................................... 4

5. INSTALLATION ........................................................................................................ 5

6.  WIRING CONNECTION ............................................................................................... 5

7.  ADJUSTMENT PROCEDURE ......................................................................................... 6

7.1.  MANUAL OPERATION .............................................................................................................................6

7.1.1.  GENERAL PROCEDURE .............................................................................................................6
7.1.2.  ZERO & SPAN ...............................................................................................................................6
7.1.3. DEADBAND ..................................................................................................................................6
7.1.4.  RESTART LIMITING TIME ............................................................................................................6
7.1.5.  COMMUNICATION ERROR OPERATION ....................................................................................7

7.2. CC-Link .....................................................................................................................................................7

7.2.1.  STATION NO. .................................................................................................................................7
7.2.2.  BAUD RATE ..................................................................................................................................7
7.2.3. COMMUNICATIONS .....................................................................................................................7
7.2.4.  BASIC OPERATING PROCEDURE ..............................................................................................8

8. MAINTENANCE ........................................................................................................ 9

9. TROUBLESHOOTING ................................................................................................. 9

10. LIGHTNING SURGE PROTECTION .................................................................................. 9

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: [email protected]

EM-4862  Rev.1  P. 1 / 9

INSTRUCTION MANUAL

Summary of Contents for MSP4C










Reviews: