background image

R30GECT1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: [email protected]

EM-9029    P. 3 / 12

INSTALLATION

 

INSTALLATION TO THE BASE

Use the Installation Base (model: R30BS).
The I/O slots are numbered in the ascending order starting 
from the one on the immediate right of the interface module 
(slot 1, slot 2...).
A code indicating the I/O slot number is assigned to each 
I/O slot and I/O data is allocated in the order of the codes.
When an I/O slot is vacant, blank data is sent or received to/ 
from the PLC, etc.

PWR COM

I/O1

I/On

 

HOW TO MOUNT THE MODULE

1) Engage the positioning guide of the module with the In-

stallation Base.

2) Pivot the module on the positioning guide and press it 

down until the lock tab clicks into place.

Positioning Guide

3) Tighten the base fixing screw using a screwdriver (stem 

length: 70 mm/2.76” or more)  (torque 0.5 N·m).

Base Fixing Screw

 

HOW TO REMOVE THE MODULE

1) Loosen the base fixing screw using a screwdriver (stem 

length: 70 mm/2.76” or more).

Base Fixing Screw

2) While pressing the projection on the lock tab, push the 

module upward.

3) Detach the positioning guide of the module from the In-

stallation Base.

Lock Tab

Summary of Contents for EtherCAT R30GECT1













Reviews: