background image

 

 

MCM JR-2 Current Interrupter 

 
 

                    

11640 US Hwy 1, Sebastian FL 32958 

                                                            Tel: 772-794-9448 ~ Fax: 772-589-9072  
                                            E-mail: 

[email protected]

 ~ Web Site: 

www.mcmiller.com

 

                                                 

Instruments and Equipment for the Corrosion Engineer         

 

 

Warranty 

 

 

M.C.  Miller  Co.,  Inc.  warranties  each  new  instrument 
manufactured  and  sold  to  be  free  from  defects  in  material, 
workmanship,  and  construction  except  for  batteries,  which 
may  be  contained  therein.  When  used  in  accordance  with 
this Operating Manual the unit will perform to applicable  
specifications for a period of one year after shipment.  

If  examination  by  M.C.  Miller  Co.,  Inc.  discloses  that  the 
product is defective, then its obligation is limited to the repair 
or replacement of the defective unit or its components at the 
option of M.C. Miller Co., Inc. 

M.C.  Miller  Co.,  Inc.  is  not  responsible  for  products,  which 
have  been  subject  to  misuse,  alteration,  accident,  or  for 
repairs not performed by M.C. Miller Co., Inc.  

Instruments  must  be  returned  properly  packed  with  the 
transportation charge prepaid to: 

M.C. Miller Co., Inc. 

11640 US Hwy 1 

Sebastian, Florida 32958

 

Return  transportation  charges  will  be  F.O.B.  factory.  No 
parts  shall  be  returned  without  prior  authorization,  which 
shall be furnished upon request.  

The  foregoing  warranty  constitutes  M.C.  Miller  Co.,  Inc.'s 
sole  liability  and  is  in  lieu  of  any  other  warranty  of 
merchantability  or  fitness.  M.C.  Miller  Co.,  Inc.  shall  not  be 
responsible  for  any  incidental  or  consequential  damages 
arising from any breach of warranty.  

Summary of Contents for 12830




























Reviews: