Lynx D VD 5002 Reference Manual Download

Page: 19 / 22

Reference Manual D VD 5002 Version1.1

Page 19

Available Options

Below is a list of related products for the D VD 5002
CardModule. Please refer to product brochures or

our web site for more detailed information.

Model Description

R FR 5010

Series 5000 Rack Frame (empty) with single
power supply

R PS 5010

Redundant power supply for the R FR 5010
Card Frame

R CT 5020

Rack controller for the R FR 5010 Card
Frame

R CT 5010

Rack Bus Extension for the R FR 5010 Card
Frame. In combination with R CT 5020

Parts List

Due to the very dense design and miniature

surface mount technology the module is not field

serviceable. The information for a replacement
assembly is below.

D VD 5002 CardModule (complete)

Description

Dual SDI DA w/ monitoring

Model Number

D VD 5002

Part Number

6.155.008.235

Sub Assemblies:

D VD 5002 Processing Board only (BS 5013)

Part Number

6.155.010.211

Rear Connection Panel for D VD 5002 (MA5001_B)

Part Number

6.155.008.371

Summary of Contents for D VD 5002























Search results

Summary of Contents for D VD 5002

Reviews:

Related manuals for D VD 5002

Brands by name

Popular brands

Lynx D VD 5002, Reference Manual

Search results

Summary of Contents for D VD 5002

Reviews:

Related manuals for D VD 5002

Brands by name

Popular brands