background image

19

LYMAN PRODUCTS WARRANTY

This warranty covers all products manufactured and supplied by Lyman Products as well as all 
its associated brands. Your Lyman Product has been produced under rigid standards of manufac-
ture and inspection and are warranted against material defects and workmanship. 

Products which are manufactured by Lyman Products are covered by a LIMITED LIFETIME 
WARRANTY.  This warranty is extended only to the original consumer purchaser. All Lyman 
products are intended for non-commercial use by hobbyists. Any other use of these products will 
void the warranty. Should you believe that your product is defective in material or workmanship 
you must return the product to Lyman Products Corporation postage paid for evaluation.  (See 
Return Policy)  If the returning defective product meets the criteria of this warranty the product 
will be repaired or replaced at Lyman Products’ option at no charge, parts and labor are included.

Lyman reloading tools and accessories are warranted against defective materials and workman-
ship only.  This warranty is void if the product:
(1) has been damaged by accident or unreasonable use, neglect, improper service or other causes 
not arising out of defects in material or workmanship; 
(2) has been altered or repairs have been made or attempted by someone other than authorized 
factory personnel
(3) is used commercially
(4) has been altered or defaced in any way. 

THE LIMITED LIFETIME WARRANTY DOES NOT COVER DEFECTS OR DAMAGE 
RESULTING FROM: COMMERCIAL USE, ABUSE, IMPROPER INSTALLATION, 
MODIFICATION, LACK OF CARE, MISUSE OR NORMAL WEAR AND TEAR. THE 
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE ARE LIMITED TO THE DURATION OF THIS LIMITED LIFETIME 
WARRANTY. LYMAN PRODUCTS CORPORATION IS NOT LIABLE FOR DAMAGES 
IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT AND UNDER NO 
CIRCUMSTANCES SHALL LYMAN PRODUCTS CORPORATION BE LIABLE FOR 
CONSEQUENTIAL OR INCIDENTAL DAMAGES. HOWEVER, SOME STATES DO NOT 
ALLOW LIMITATIONS ON INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE 
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may also have other rights which vary 
from state to state. Lyman Products is proud of our workmanship and quality that we build 
into our products. While our products are warranted against defective materials and workman-
ship we cannot warranty;
  • Product sales to government or local law enforcement institutions or agencies 
  • Rust or corrosion 
  • Obstructions in barrels   
  • Finishes or Slides
  • Sales of the product to second or subsequent owners
  • Items purchased second hand 
  • Ammunition   

Lyman Products will replace any missing hardware free of charge even if you lose it.
Lyman Products is so confident you will be happy with your purchase that if for any reason you 
are not we will take back the product for a full refund within 30 calendar days of your original 
purchase. Receipt must be provided. Please contact Customer Service at 800-225-9626.

Summary of Contents for All-American 8





















Reviews: