manualshive.com logo in svg

Luxul XMS-1008P, User Manual

Share
Download
Luxul XMS-1008P User Manual Download Page 33

luxul.com  |  357 South 670 West  |  Suite 160  |  Lindon, UT 84042  |  p: 801-822-5450  |  f: 801-822-5460

User Guide

33

5.13.2 Change Password 

Change Password:

 Modifi es the password for switch login

 

Old Password:

 Enter the old password (Default password is “admin”) 

 

New Password:

 Enter the new password 

 

Confi rm New Password:

 Re-enter the new password 

 

NOTE: 

A password can consist of up to 15 alphanumeric characters. 

5.13.3 Power Save

 

 

Power Save:

 Check to enable or uncheck to disable the power save mode

 

Apply:

 Enables or disables the power save mode

5.13.4 Upgrade

Firmware Upgrade

Please visit the Luxul website to check for fi rmware upgrades and obtain upgrade 
instructions. 

1.  Go to the Luxul website (www.luxul.com/support) and download the new 

version of fi rmware to your computer

2. Click “Browse” to locate the fi rmware fi le on your computer  
3. Click “Upgrade” to perform the update 

Summary of Contents for XMS-1008P









































Reviews:

No comments

Brands by name

Popular brands

Load more brands