background image

There are no wear parts in the device. Maintenance and service must be performed only by 

an authorized service partner.  

 

  

  

  

 

  

 

 

 

Before operate this unit, please carefully read this users guide and keep if 
needed in future. 

It’s necessary to respect following rules.  

 

 

The disposal of the device after lifecycle could damage the environment, need to 
take it to special company for recycling or return to authorized dealer.  

 

 

The products referred to in this manual conform to the European Community 
Directives and are therefore marked with CE logo.  

  

 

Keep this device away from children and unauthorized users, the manufacturer  
will not take responsibility for the damage due to any disregard of the information 
provided in this manual and wrong operation.  

  

 

Before operate the device, please make sure the fixture is in good housing, 
ensure pan and tilt can rotate in its complete range.  

  

 

    --0.5m 

 

Please make sure minimal 0.5m distance need to kept between the fixture to any 
flammable material.  

  

The device can only run with 100-

240V voltage, 50/60 Hz power, don’t connect 

to any other wrong power. Disconnect the device from main power before open 
the shield or maintenance.  

  

The device is designed only for indoor usage, please keep it away from 
moisture. Do not expose the device under the sun or directly to any other lighting 
source.

 

 

  

  

Never look directly into the projecting lens when the fixture is power on, the light 
may trigger epileptic seizures in photosensitive persons or persons with 
epilepsy. Especially at beam effect, extreme caution and observance of these 
safety instructions is mandatory.  

   

 

Don’t put or install the device on a surface that subject to vibration or bumps.  

 

Ta=45

 

The device is supposed to work in the temperate range -15° C and +45° C, do 
not use the device when the temperate exceed this range.  

 

 

Safety I class device, need to be earth connected.  

 

 

 

When the fixture is hanged overhead, the safety rope must be fixed to the bottom 
of the device to the appropriate fixing point.  

   

 

Always carry the device by the bracket, do not take the head directly for 
transportation.  
  

Summary of Contents for PANEL180TW















Reviews: