background image

Safety Notes  

  

Each person which is responsible for the installation, the usage of service of this unit must be 

qualified and has to follow the instruction in this manual.  

This device is not meant for residential use. 
 

Be careful when using the device. You risk an electrical shock from high voltage, if you touch 

the wires! The device has left our company in manufactured proofed state. To maintain this 
status and to ensure a permanent safe operation, it is absolutely necessary to follow the 
safety instructions and warnings in this manual.   

Errors caused by not following these instructions are not covered by the warranty. The 

manufacturer will not accept liability for any resulting defects or problems.   

•  Keep the unit away from radiators or other heat sources!  
•  If the unit has been exposed to tremendous temperature changes (e.g. after 

transportation), do not turn the device on immediately. The resulting condensation 
could damage the unit. Don’t switch the unit on until the device reaches room 
temperature.   

•  This device belongs to protection class I. This appliance must be grounded while in 

use to protect the operator from electrical shock. 

•  Make sure that the cable has never been squeezed or damaged by sharp objects. 

Check the device and the cables regularly.   

•  If the cable is damaged, it must be replaced immediately by the manufacturer, its 

service agent or a qualified person in order to avoid danger.   

•  Ensure that wires never come in contact with other wires! Handle the power cord and 

all connections with caution!  

•  Make sure that the line voltage is not higher than the voltage specified in this manual.   
•  Disconnect the unit from the AC mains when it is not in use or when cleaning it.  

Disconnect the connection only by pulling the cable plug.   

•  Maximum 12A interconnected   

•  Dry locations only. 

•  Do not under any circumstance connect anything other than a special updater to the 

USB-C port on the back of the fixture. Doing so will damage your connected device.

 

 

Risk of burns!   
Do not touch the unit during operation! The housing may reach high temperatures!   

Risk to health!   
Never look directly into the light source. Especially epileptics risk an epileptic shock. 

Disconnect the unit from the AC mains when not in use or when cleaning it.   

Defects caused by modifications of the device by unqualified handling or an unqualified 

person are not covered by the warranty.   

Keep the product away from children and unskilled people.   

Summary of Contents for PANEL180TW















Reviews: