![Luxibel LX119 User Manual Download Page 6](http://html1.mh-extra.com/html/luxibel/lx119/lx119_user-manual_1952251006.webp)
LX119
V. 01 – 19/06/2014
6
©Velleman nv
7.2
Auto Mode
If no DMX control signal is present at the DMX input
[3
or
4]
, the unit independently runs through its
show programme (if the blackout mode is switched off).
1.
Press MENU until <AUTO> appears on the display. Press ENTER to confirm.
2.
Select one of the auto programmes (programme 0-4) with UP or DOWN. Press ENTER to confirm.
3.
Set the running speed (0-100 %) with UP or DOWN. Press ENTER to save the setting.
IMPORTANT: The auto programmes 0-4 are fully pre-programmed and will not be altered by changes.
Instead, the <MANU C> mode allows combining the colours RGBWAP (red, green, blue,
white, amber, purple).
1.
Press MENU until <STATIC> appears on the display. Press ENTER to confirm.
2.
Select <MANU C> with UP or DOWN and press ENTER to confirm.
3.
Select the colour (RGBWAP) with UP or DOWN and press ENTER to confirm.
4.
Set the value (000-255) with UP or DOWN. Press ENTER to save the setting.
5.
Press MENU to go back.
7.3
Static Mode
This unit has the ability to accept custom static colour settings.
1.
Press MENU until <STATIC> appears on the display. Press ENTER to confirm.
2.
Select <FIXT C> with UP or DOWN and press ENTER to confirm.
3.
Select the colour with UP or DOWN and press ENTER to confirm.
4.
Press MENU to go back.
7.4
Master/Slave Mode
This mode allows you to link up several units together without using a controller. Choose the first in the
chain to function as master unit; other connected units will work as slave units with the same effect.
1.
Press MENU until <M&S> appears on the display. Press ENTER to confirm.
2.
According the master or slave unit, select <MASTER> or <SLAVE> with UP or DOWN and press
ENTER to confirm.
3.
Select the desired programme (see
7.3 Auto Mode
).
4.
Use standard DMX cables to daisy chain your units together via the DMX connections
[3
or
4
+
5
or
6]
on the rear of each unit. We suggest using a terminator on the last unit for longer cable runs
(see
7.10 Construction of the DMX Termination
).
7.5
Linking
Several units may be interconnected in order to control all further slave units to the same effect as the
master unit.
1.
Connect the DMX output
[5
or
6]
of the master unit to the DMX input
[3
or
4]
of the first slave unit
using an appropriate cable with XLR connector.
2.
Connect the DMX output
[5
or
6]
of the first slave unit to the DMX input
[3
or
4]
of the next slave
unit using an appropriate cable with XLR connector, until all units are connected in a chain.
7.6
DMX Configuration
This device is equipped with different DMX configurations.
1.
Press MENU until <CHANNEL> appears on the display. Press ENTER to confirm.
2.
Select the desired DMX configuration (6ch, 8ch, 12ch, HSV or HSI) with UP or DOWN and press
ENTER to confirm.
3.
Refer to chapter
7.11 DMX Value per Channel
to set each channel.
7.7
DMX Mode
1.
Press MENU until <ADDRESS> appears on the display. Press ENTER to confirm.
2.
Select the desired value (001-512) with UP or DOWN (hold UP or DOWN pressed to scroll rapidly)
and press ENTER to confirm.
3.
Press MENU to go back.
All DMX-controlled devices need a digital start address so that the correct device responds to the
signals. This digital start address is the channel number from which the device starts to “listen” to
the DMX controller. The same starting address can be used for a whole group of devices or an
individual address can be set for every device.