background image

 

 

 

Product Name: 

Peacock and Pot Polyresin Fountain with LED Lights 

SKU #: 

WHF548 

 

Contact: [email protected] 

Instruction Manual 

Please save this manual for future reference. 

PUMP ASSEMBLY INSTRUCTIONS:

  

 

 

Remove the pump from the package and untie the power cord. 
1.

 

Place the pump in the desired location in your pond or fountain ensuring that it is completely submerged in 
the water. If the pump is to be used in a pond, raise the pump off of the pond floor to ensure that it is above 
any dirt that will collect, as this will adversely affect the performance of the pump. 

2.

 

Adjust the flow rate (if applicable) to the maximum (+) position. 

3.

 

Connect the power cord from the pump to a properly grounded, grounding type receptacle (GFCI). 

4.

 

If necessary, readjust the flow rate to the desired level (remember to always disconnect from the power 
source before handling the pump).   

 

 

CARE & MAINTENANCE: 

1.

 

Keep the water clean – clean water will prolong the useful life of your pump. 

2.

 

Use a pre-filter on your pump if available. 

3.

 

Regular cleaning of the pump will be necessary depending upon the environment in which it is operated.   
Clean the pump when it is visibly soiled or when a noticeable drop in performance is detected. 

Failure to 

clean the pump will result in overheating of the pump and the voiding of the warranty!

 

4.

 

Before cleaning, always disconnect the pump from the power source. 

5.

 

Disassemble the pump by removing the inlet screen & the impeller housing. Remove the impeller/rotor 
assembly by gently pulling on the impeller blades. Use a soft cloth or brush to clean the area inside of the 
pump where the impeller/rotor assembly was. Clean the inlet screen, impeller housing & impeller in warm 
soapy water. Reassemble the pump and inspect for proper operation. 

 

TIPS AND TROUBLESHOOTING: 

1.

 

Ensure that the pump’s flow control switch is set to maximum (+) before operating. Once the flow is 
established, the pump can be adjusted downward to the desired level. 

2.

 

If the pump operates, but there is no flow, check to ensure the pump is fully submerged. 

3.

 

If the pump operates, but there is no flow, check the supply tubing for kinks and correct. 

4.

 

If the pump operates, but there is no flow, and if the pump is submerged and there are no kinks in the 
supply tubing, lift the pump from the water. Remove supply tubing at pump outlet and clean tubing inside 
and out if necessary. Reset pump in water (outlet side up) and once water begins to flow, re-attach the 
supply tubing.   

 
 
SAVE THESE INSTRUCTIONS 

– This manual contains important safety and operating instructions for power units.       

 
 
 

Summary of Contents for WHF548






Reviews: