Pressing this button will write default values of all
temperature programs and setup menus into the unit’s
nonvolatile memory. Take care not to unintentionally
press this button when the thermostat has been
removed from the wall plate!
4.4. PROGRAMMING
You can change the preset time/and temperatures to suit
your schedule for each day of the week. Each day has
four consecutive periods. They are Morning, Day,
Evening, and Night. Separate set points are provided for
Heat and Cool.
Fan programming is similar to temperature program-
ming. It has four consecutive periods, which are inde-
pendent of the four temperature periods. The default set-
ting for your systems fan requires it to run only as
required by your environmental system. It may be pro-
grammed to maintain a minimum run time on an hourly
basis, or run continuously.
4.4.1 WEEKDAY TEMPERATURE PROGRAMMING
●
Rotate the dial to Set Weekday Programs. The heat
and cool set points will be displayed on the left side of
the display. The start time for the displayed day will flash
to show that this is the setting currently ready for edit.
●
Use the up or down arrow keys to change the start
time for this period. One period ends at the start time of
the next period. The beginning of that period may not be
any closer to the beginning of the next period than one
15 minute increment.
●
Press NEXT to accept the displayed start time and
advance to edit the heat set point. It will be flashing.
●
Use the up or down arrow keys to change Heat Set to
the temperature you desire.
●
Press NEXT to accept the displayed heat set point to
the temperature and advance to edit the cool set point. It
will be flashing.
●
There is a minimum value that must be maintained
between the heat temperature set point and Cool temper-
ature set point. The value that must be maintained is
called the Deadband. It is programmable and may be
changed in the Installer Setup menu. If you move the
heat set point temperature to close to the cool set point
temperature the cool set point temperature will move
away from the heat set point temperature to maintain the
dead band. Conversely the heat set point temperature will
move if you adjust the cool set point temperature to
close. There are programmable limits for both heat and
cool, which you will not be able to exceed. These values
are accessible from the User Setup Menu.
●
When you have changed the Cool set point to your
desired temperature, press NEXT to advance to the next
period. Its start time will be flashing indicating that it is
under edit.
●
When all the periods for a day have been set, the start
time for the next weekday will be displayed to begin edit-
ing the settings for that day.
●
Rotate the dial back to RUN to and accept all current
values and end the programming session.
4.4.2 WEEKDAY FAN PROGRAMMING
Programming fan operation is similar to programming
the temperature periods and set points. Fan periods are
independent of temperature periods and are designated
P1, P2, P3, P4.
●
Rotate the dial to Set Weekday Programs, then press
and hold the FAN button for over 2 seconds.
●
The fan day and period will be displayed in the top
center and right portion of the screen. The bottom por-
tion will show the fan mode and start time for that period.
The fan mode for this period will be flashing to indicate
that it may be changed with the UP/DOWN arrow keys.
Choices are:
■
Auto:
default value; the fan will run only when neces-
sary for your HVAC system to maintain temperature con-
trol.
■
Program:
This mode will insure that during every
hour, the fan will run for the for at least the number of
minutes shown at the top left of the display, beginning at
the displayed time for this period until the beginning of
the next period. If your heating or cooling requirement
fulfills the minimum fan run time, additional fan run time
will not be requested. Activation of the fan when neces-
sary is done at twenty minute intervals for one third the
hourly run time.
■
On:
The On setting will run the fan continuously dur-
ing this period.
●
Set the desired Fan mode for his period. Press NEXT
to advance and edit this periods start time.
●
Use the UP or DOWN arrow keys to change the start
time. A period ends at the start time of the next period.
The beginning of a period may not be any closer to the
beginning of the next period than one 15 minute incre-
ment.
●
Press NEXT to advance and set the minimum fan run
time if this period is to use program mode.
●
Pressing NEXT again will bring you to the next period’s
mode.
●
When all the periods for a day have been set, the start
time for the next weekday will be displayed to begin edit-
ing the settings for that day.
●
The sequence of days that you may program pro-
gresses the weekdays MON - FRI, and repeats.
●
Then press and hold the FAN button for over 2 sec-
onds to return to Weekday temperature editing or rotate
the dial back to RUN to and accept all current values and
end the programming session.
4.4.3 WEEKEND PROGRAMMING
Weekend programming is identical to weekday program-
ming except rotate the dial to set weekend programs, and
the sequence of days that you may program is SAT, SUN
and then repeating this two day sequence.
15
