manualshive.com logo in svg

Lutron Electronics Sivoia QED Roller 64, Installation Instructions Manual

Share
Download
Lutron Electronics Sivoia QED Roller 64 Installation Instructions Manual Download Page 3

SIVOIA QED

TM

Roller 64 Pocket Mount Installation

Instructions

2

Warning:

Incorrect installation can lead to severe injury, follow all installation instructions.

Notes:

•  The Sivoia QED Roller 64 must be used only with window systems approved by Lutron.

•  There must be a clearance of at least 1.3 feet (0.4 meters) between the fully lowered system 

and any permanent object.

•  Installation shall be executed by a qualified electrician according to national wiring rules.

•  Before shade installation, remove any unnecessary cords and disable any equipment not 

needed for powered operation. The Sivoia QED Roller 64 has a maximum rated operating 
time of 8 min.

•  The Sivoia QED Roller 64 must be used only with window systems approved by Lutron, 

and should not be taken appart from the window system.

• 

Codes: 

Install in accordance with all local and national electrical codes. 

• 

Environment: 

Ambient operating temperature: 0-40°C, 32-104°F, 0-90% humidity, non-condensing.

Indoor use only.

Sivoia QED

TM

|

Roller 64

TM  

Pocket Mount

Installation Instructions (continued)

 

Summary of Contents for Sivoia QED Roller 64

























Reviews:

No comments

Brands by name

Popular brands

Load more brands