manualshive.com logo in svg

Lutron Electronics Sivoia QED Roller 64, Installation Instructions Manual

Share
Download
Lutron Electronics Sivoia QED Roller 64 Installation Instructions Manual Download Page 2

Sivoia QED

TM

|

Roller 64

TM  

Pocket Mount

Installation Instructions

SIVOIA QED

TM

Roller 64 Pocket Mount Installation

Instructions

1

Tools Required:

Tape Measure

1/4” Hex-Head Driver

Wire Cutter/Stripper

Level

Pliers

Power Drill

#2 Phillips Screwdriver

Sivoia QED

™

Roller 64

Shade Brackets with Retaining Screws

(5) Mounting Screws 
(#8x1-3/4" (#8x44mm)
Hex Head Screws)

(1) 7 Pin Terminal Block

(1) Programming Stylus

(1) Screwdriver

(1) Pocket

(1) Flap

(2) 4” (102mm) Cable Ties

Notes:

1) Complete wiring and programming information can be found in the Sivoia QED Wire and 

Programming Guide, P/N 045-038 or at www.lutron.com.

2) The Electronic Drive Unit (EDU) will need to be powered to complete installation.

Box Contents:

(2) Bracket Leveling Spacer (2) Cable Tie Anchor

(2) Pocket Endcaps (if applicable)

Summary of Contents for Sivoia QED Roller 64

























Reviews:

No comments

Brands by name

Popular brands

Load more brands