background image

R

S p e c i f i c at i o n   S u b m i t ta l

page

Job Name:

Job Number:

Model Numbers:

QS System

QSE-CI-NWK-E

Control Interface

369373b   2   06.21.12

Specifications

Power

• IEC PELV/NEC

®

 Class 2

• Operating voltage: 12–24 V   65 mA

QS Link Limits

• The QS wired communications link is limited to 

100 devices and 100 zones. Each QSE-CI-NWK-E 

control interface counts as 2 devices and 2 zones.

• Each QSE-CI-NWK-E control interface consumes 

 

2 power draw units (PDU) on the QS link. Refer 

to the QS Link Power Draw Units Specification 

Submittal (Lutron PN 369405, at www.lutron.com) 

for more information.

• The maximum wiring length for the QS link is 2000 ft 

(610 m).

Environment

• 32 to 104 °F (0 to 40 °C). 

• Relative humidity less than 90% non-condensing.

Integration Features

• Monitoring: Current scene, zone level, button 

presses, shade group levels.

• Control: Scene selection, scene lockout, zone 

lockout, sequencing, zone raise/lower, master raise/

lower, set shade group level, simulate button press/

release.

For the full list of features and commands, please 

refer to the protocol document on the 

accompanying CD, also available at  

www.lutron.com.

RS232 Connection

• Standard 9-pin female serial connector on interface. 

• 50 ft (15 m) maximum serial cable length.

• Dip switches are set at factory, all Off. 

• Dip switches are used to set RS232 baud rate:

DIP Switch Settings for RS232 Baud Rate

115200 (default)

38400

19200

9600

 

Ethernet Connection

• Standard CAT5 (or better) cable, 328 ft (100 m) 

maximum, connects the QSE-CI-NWK-E interface to a 

PC or other Ethernet source.

• Supports MDI/MDIX auto-crossover (no crossover 

cable needed).

• Auto-negotiation of 10 or 100 Mbps speed and full- or 

half-duplex operation.

• Default IP address is 192.168.250.1. Can be changed 

using the Lutron DeviceIP tool located on the 

accompanying CD.

Note: 

Either the RS232 or the Ethernet can be used, 

but not both.

115200

38400

19200

9600

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

115200

38400

19200

9600

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

115200

38400

19200

9600

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

115200

38400

19200

9600

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

1   2   3   4   5   6   7   8

Summary of Contents for QSE-CI-NWK-E







Reviews: