Wiring
A
. Single Line Wiring
2
Connect sensor switch
WARNING! Shock Hazard.
May result in serious injury or death.
Turn power OFF at circuit breakers before installing the unit.
1
Turn power OFF
I
I
I
O
O
O
Dual Circuit
Dual Technology Sensor
Switch Installation Guide
Lighting
120-277 V
~
50 / 60 Hz 6 A
Fan
120 V
~
50 / 60 Hz 4.4 A 1/6 HP
Combined lighting and fan load
120 V
~
50 / 60 Hz 4.4 A
MS-B202 WMS-B202
Occupancy
P/N 032568 Rev. A
10/2020
Limited Warranty
(Valid only in U.S.A., Canada, Puerto
Rico, and the Caribbean). Lutron will, at its option, repair or
replace any unit that is defective in materials or manufacture
within five years after purchase. For warranty service, return
unit to place of purchase or mail to Lutron at 7200 Suter
Rd., Coopersburg, PA 18036-1299, postage pre-paid. This
warranty is in lieu of all other express warranties, and the
implied warranty of merchantability is limited to FIVE years
from purchase. This warranty does not cover the cost of
installation, removal or reinstallation, or damage resulting
from misuse, abuse, or damage from improper wiring or
installation. This warranty does not cover incidental or
consequential damages.
Lutron’s liability on any claim
for damages arising out of or in connection with the
manufacture, sale, installation, delivery, or use of the
unit shall never exceed the purchase price of the unit.
This warranty gives you specific legal rights, and you may
have other rights which vary from state to state. Some
states do not allow the exclusion or limitation of incidental
or consequential damages, or limitation on how long an
implied warranty may last, so the above limitations may
not apply to you.
Lutron and Maestro are trademarks or registered
trademarks of Lutron Electronics Co., Inc. in the US
and/or other countries.
© 2013-2020 Lutron Electronics Co., Inc.
Major motion coverage:
30 ft × 30 ft (9 m × 9 m) [900 ft
2
(81 m
2
)]
Minor motion coverage:
20 ft × 20 ft (6 m × 6 m) [400 ft
2
(36 m
2
)]
3
Turn Power ON
I
I
I
O
O
O
Troubleshooting
Symptoms
Possible Solutions
Sensor switch is
unpowered, or is
powered, but does
not turn lights ON.
• If installed in a 3-way with another
mechanical switch, be sure to
rewire the mechanical switch using
Wiring step 2B.
Power can’t be
switched ON or OFF
with newly installed
sensor switch.
• Check wiring; neutral wire must be
connected for product to function.
Lights do not turn
ON when space is
occupied.
• Off-While-Occupied mode is
Enabled and the timeout has not
expired.
• Sensor mode is set to vacancy.
• Sensor is set to one of the Ambient
Light Detection (ALD) settings
and the room is too bright for the
current light level setting.
• Sensor does not have full view of
the room. Move objects blocking
sensor’s line-of-sight.
•
Before installing wallplate, program all desired settings. See back for programming instructions.
• For additional wiring instructions, including wiring for two separate breaker feeds, please visit
www.lutron.com/DTMaestroInstall
•
Rewire your mechanical switch in a 3-way. 3-way wiring for sensor switch is different than
traditional 3-way wiring.
For additional features, wiring help,
troubleshooting, and product information
please visit:
www.lutron.com / DTMaestroInstall
4
Wait for 2 minutes
•
The sensor switch will manually control the load after the first 10 seconds.
• Once power has been restored, the sensor switch will automatically control the
load after the first 2 minutes.
Important Notes
Please read before installing.
1.
Neutral wire required.
2.
Device will not function if Black wires (Circuit 1/
Line 1) are not wired.
3.
This product is rated to control 6 A
per circuit
.
Circuits may NOT be wired in parallel to control
loads greater than 6 A.
4.
When power is applied, the sensor switch can be
manually turned on or off after the first
10 seconds and will automatically control the
load after 2 minutes.
5.
CAUTION:
Risk of Electric Shock
— More than
one disconnect switch may be required to de-
energize the equipment before installing the unit,
rewiring, or replacing bulbs.
6.
The sensor switch requires an unobstructed view
of the room and line-of-sight to detect motion.
7.
Hot objects or moving air currents can affect the
performance of the sensor switch and may cause
the sensor to turn on unexpectedly or maintain
its current state longer than desired.
8.
CAUTION:
To reduce the risk of overheating and
possible damage to other equipment,
DO NOT
use to control receptacles.
9.
Install in accordance with all national and local
electrical codes.
10.
For indoor use only. Operate between 32 °F and
104 °F (0 °C and 40 °C).
11.
Clean with a soft damp cloth only.
DO NOT
use
any chemical cleaners.
B
. 3-Way with Mechanical Switch
m
30
15
5
1
Occ
Lrn
Fixd
Vac
Mode
Hi
Med
Low
Off
Hi
Med
Low
Min
PIR
Neutral
Black
1
Black
1
Load 1
Load 2
Green
Black-Orange
White
Line/Hot
Blue
Black-Orange
m
30
15
5
1
Occ
LRN
Fixd
Vac
Mode
Hi
Med
Low
Off
Hi
Med
Low
Min
PIR
m
30
15
5
1
Occ
Lrn
Fixd
Vac
Mode
Hi
Med
Low
Off
Hi
Med
Low
Min
PIR
Black
1
Blue
Ground
Two Circuit
Switch
Green
Ground
120–277 V
~
50 / 60 Hz
Line / Hot
Load 2
Standard
Mechanical Switch
2,3
Black
1
Yellow jumper
wire (included)
Different
color
screw
Neutral
Load 1
White
Black-Orange
Two Line Wiring:
Wiring must comply with NEC code for wiring Multiple Branch Circuits: Where two or more branch
circuits supply devices or equipment on the same yoke, a means to simultaneously disconnect
the ungrounded conductors supplying those devices shall be provided at the point at which the
branch circuits originate.
Two circuits, each rated at:
Black-Orange
Ground
1
Device will not function if Black wires are not wired.
2
Mechanical switch may be wired to either circuit, and will control both.
Do NOT
wire mechanical switch to both circuits.
3
You may use no more than one mechanical switch with a Dual circuit Dual Tech sensor switch.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
www.lutron.com
English
