Lunos Skalar Series Installation Directions Manual Download Page 10

10  

 

E

 1

2

8

/0

5

.1

1

 

LUNOS Lüftungstechnik GmbH für Raumluftsysteme 
Wilhelmstr. 31-34 
13593 Berlin 
Germany 

Tel.:      0 30 / 36 20 01 - 0 
Fax: 

0 30 / 36 20 01 - 89 

 

Mail:      [email protected] 
Site: 

http://www.lunos.de 

Filter change

 

• 

Continuous  red  light  up  of 
illuminated  display indicates 
a dirty filter 

• 

Take  of  the  front  cover 
plate,  remove  filter.  Insert 
new  or  cleaned  filter.  Dirty 
filters can be  cleaned,  e.g. 
in a washing machine. 

• 

Operate  button  for  3  sec-
onds with a pencil or similar 
to turn off the display illumi-
nation 

• 

Replace  the  front  cover 
plate 

 
Never operate the system 
without a filter!  

Illuminated 
display 

Button 

Front cover plate 

Grid cover frame 

Filter 

Run-out time setting:

 For ventilators with run-out time 5/ZII 

Caution! Only adjust the switch when ventilator is in the dead condition! 

 

Factory settings

 

:  

 

 

 
 

To change settings: 

1. Take the front cover plate off 
2. Draw the cap off of the electrics housing 
3. Make the wanted settings 
4. Re-assemble in the opposite succession

 

• 

Switch-on delay 120 sec 

• 

Run-out time 15 min 

• 

Inverse operation OFF 

• 

Interval switching OFF 

White toggle switch 

Remove cap with 
a screwdriver 

Electrics housing 

Cap  

Interval ON every 4 hrs for 30 min * 

Interval OFF 

Run-out time 15 min 

Run-out time 6 min 

Inverse operation 30 min after run-
down after the room is left * 

Inverse operation OFF 

Switch-on delay 120 sec 

Switch-on delay 0 sec 

Accessory and replacement parts 

Filter, pack of 3 

 

 

 

 

 

 

 

 

2/FSI-R  

Order no. 

039 721 

Silvento decor plate incl. filter display

 

 

 

 

 

 

 

 

 

2/S 

 

Order no. 

039 551 

Silvento decor plate with movement detector 

 

 

 

 

 

 

 

2/SB   

Order no. 

039 578 

 

Illuminated display         Button 

Ventilator with movement detector

Button and illuminated display are in the grid cover frame 

Ventilator with step switching, run-out time or 
humidity control:

 Button and illuminated display 

are in the electrics housing 

Cleaning

 

Wipe the front cover plate and grid cover frame with a dry, soft cloth when appropriate. 

Filter change and cleaning are not to be carried out by children or people who cannot manage this with certainty 
because of their physical, sensorial or mental ability, or their inexperience or lack of appropriate knowledge

 

 

* I

ndependent of the set  

   adjusted run-out time 

Summary of Contents for Skalar Series











Reviews: