background image

position the image is at its best.  After that, rotate the 
Objective Lens (1) also until the image is at its best.  You may 
have to repeat the process again, until the image is sharp and 
clear.  Once the clear image is obtained, you no longer need to 
adjust the Ocular Ring, just rotate the front objective lens ring 
to adjust according to the distance of the object you are 
viewing. 
 
 
 

USING INFRARED ILLUMINATOR: 

 
Your night vision monocular is equipped with a built-in 2-stage 
Infrared illuminator light (2).  This light operates in a spectrum, 
which is invisible to a human eye, however with the help of the 
tube, located inside the unit, you will see a beam of light when 
looking though the ocular lens.  This Infrared light is here to 
assist your viewing over the very short distances in especially 
dark conditions, where there is not enough light for the tube to 
amplify.  
 
To turn the Infrared illuminator on, first turn on the unit by 
rotating the Switch (3) one dial to ON position and then you must 
slide forward the top moving plate of the switch and at the same 
time rotate the switch (3) one more dial to IR position.  Please 
note that if you do not slide the top moving plate of the switch, 
you will not be able to switch on the IR illuminator.  This feature 
preserves the battery life by preventing accidentally turning on 
the IR light.  When looking through the Eyecup (6), you will 
notice a little red indicator turning on – this is to remind you that 
the infrared light is on.  You may further rotate the Switch (3) to 
IR+ position to increase the brightness of the IR illuminator 
(IMPORTANT: to switch between IR and IR+ positions you are not 
required to slide the top moving plate of the Switch. 
 
To turn the infrared light off, press the same button again and 
make sure the red light indicator in the field of view is off. 
 
When using the built-in infrared illuminator it is important to 
remember that it is only meant to be used on very short 
distances.  As the distance increases, the intensity of the 
infrared light fades away. 
 
 
 

AUTOMATIC GAIN CONTROL: 

 
Please note that the unit is equipped with the special Auto-Gain 
control, which would not allow you to turn on the unit without 

Summary of Contents for LN-EM1-MS









Reviews: