Please read all instructions prior to installation and keep for future reference!
2
2.1
Remove the eight Phillips screws from the top of the driver
housing and pull the cover off to expose the driver wires.
housing
cover
Phillips screw
2.1
24V DC, 4.0A
Max. wattage
96 W
1
1.1
LED Driver can be mounted vertically or horizontally. With a
minimum of 2" clearance around LED Driver to provide proper
air circulation.
Before installing, check the label and ensure the LED
Driver has the proper input voltage, output voltage, and
wattage for the job. Check the wire markings to ensure
they match the wiring diagram below. Refer to table
above for the maximum loads!
2” min.
2” min.
2” min.
5.2”
2.6”
13.4”
14.4”
Input
120 - 277V AC, 1.1A, 50/60Hz
Output
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
REV0.0 11142019
This LED Driver is to be installed in accordance with Article 450 of the National Electrical Code. The LED Driver must be
installed in a well ventilated area and free from explosive gases and vapors. Proper operation requires the free flow of air. As
this LED Driver is hardwired, it should only be installed by a qualified electrician. Suitable For Damp Location.
3
3.1
Connect the 120-277V AC
power into the housing from
the electrical panel.
Followed by connecting the
24V DC low voltage
conduit, one for the LED &
other for the controller
wires. Refer to the diagram
below to make all the
proper wiring connections.
Page 1 of 2
Models PS010TW-96-24
Wiring diagram connecting
to LLDW36 LineLED
gray-
Vin1-
black
Vin1+
red
warm-
blue
cool-
blue
cool+
yellow
Vin2-
black
Vin2+
red
SLD-DIM-TW2
Tunable white LED PWM dimming module
Dimming range: 0-100%
0/1-10V control1, 0/1V=0% light output
10V=100% light output
0/1-10V control2, 0/1V= 100% warm
10V=100% cool
PWM Output to LED Modules (8-48V PWM, 1K Hz)
0-10V controller
+
-
-
WW
CW
L
N
GRD
-
+
120 - 277V AC
LED Driver 96W max
PS010TW-96-24 power supply
24VDC
reference LineLED wire lead
labels to determine polorarity
LLDW36 Dynamic white
gray-
control input 2
(color temp)
control input 1
(intensity)
warm+
yellow
24VDC
Wiring diagram connecting
to LLDW52 LineLED
gray-
SLD-DIM-TW2
Tunable white LED PWM dimming module
Dimming range: 0-100%
0/1-10V control1, 0/1V=0% light output
10V=100% light output
0/1-10V control2, 0/1V= 100% warm
10V=100% cool
PWM Output to LED Modules (8-48V PWM, 1K Hz)
0-10V controller
L
N
GRD
-
+
120 - 277V AC
LED Driver 96W max
PS010TW-96-24 power supply
gray-
control input 2
(color temp)
control input 1
(intensity)
LLDW52 Dynamic white
+
+
Vin1-
black
Vin1+
red
warm-
blue
cool-
blue
cool+
yellow
Vin2-
black
Vin2+
red
warm+
yellow
PLENUM FOR
SUCH USE IN
ACCORDANCE
WITH UL2043
Tunable White two 0-10V Channel 96 watt LED Driver -
Installation Instructions
T 224.333.6033
www.opticarts.com
