manualshive.com logo in svg

Lucent Technologies Stinger STGR-LIM-48, Manual, Page: 40 / 52

Share
Download
Lucent Technologies Stinger STGR-LIM-48 Manual Download Page 40

2-2

Stinger®

 

SHDSL 48-Port and 72-Port Line Interface Modules (LIM) Guide 

Configuring LIM and LIM Port Redundancy

Configuring LIM redundancy

The resulting system has 13 active ADSL LIMs and one spare that can be substituted 
for any one of the 13 LIMs if a failure occurs.

In the same way, a unit can be equipped with the following module pairs:

■

6 SDSL LIM–LPM-RP pairs

■

1 SDSL–PSM pair or SDSL–CLT module pair

■

6 ADSL LIM–LPM-RP pairs

■

1 ADSL–PSM pair or ADSL–CLT module pair

The resulting system has six active SDSL LIMs and six active ADSL LIMs, with one 
spare LIM of each type available in case of failure. 

When the redundancy function is invoked, the primary LIM is deactivated. Its logical 
connections are terminated and reestablished on the spare (secondary) LIM. When 
the redundancy function is disabled, the spare LIM is deactivated. Its logical 
connections are terminated and reestablished on the primary LIM.

Figure 2-1 illustrates LIM redundancy for a failed SDSL LIM in slot 4 of a Stinger FS 
chassis. A Stinger LS chassis has its LPMs and PSMs or CLT modules next to its LIMs 
rather than behind them as shown here.

Figure 2-1.  LIM redundancy in a Stinger FS unit

Overview of the lim-sparing-config profile

When a Stinger unit is booted, it checks for the presence of PSMs or CLT modules. A 

lim-sparing-config

 profile is created for each PSM or CLT module detected. You 

manage LIM redundancy by configuring the 

lim-sparing-config

 profile on a spare 

LIM of the same type as the LIM to be backed up.

Following is a listing of a 

lim-sparing-config

 profile with all parameters set to their 

default values:

Summary of Contents for Stinger STGR-LIM-48





















































Reviews:

No comments