Lucent Technologies PARTNER Advanced Communications System Release 1.0 Programming And Use Instructions Download Page 48 | Manualshive

Page: 48 / 365

background image

This chapter explains how system and standard phones work with the system, as
well as combination extensions where more than one phone or standard device
is installed. In addition, basic call handling features and dial-code features are
listed at the end of this chapter. See the feature name in Chapter 5 for details
about a specific feature.

System Telephones

PARTNER-model phones have several buttons and indicators in common. The
following pages explain where they are and how they work. For information
about an MLC-6, MLS-model, or TransTalk 9000-series phone, refer to the
documentation that came with the phone.

Learning About Telephones

3

Learning About Telephones

3-1

«
...
46
47
48
49
50
...
»

Summary of Contents for PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Reviews:

No comments

Related manuals for PARTNER Advanced Communications System Release 1.0

Brand: Xantrex Pages: 4

Brand: Xantrex Pages: 20

Brand: Radionics Pages: 14

Brand: Fender Pages: 6

Brand: eMoMo Pages: 2

Studio 500 Series

Brand: JAMO Pages: 16

Brand: NAIM Pages: 51

ProAudio ARX7570z

Brand: Clarion Pages: 29

Brand: TANDBERG Pages: 172

Brand: iPECS Pages: 101

MICHELANGELO BT A 60

Brand: BFT Pages: 84

SwitchPoint Infinity 2

Brand: Stryker Pages: 82

Brand: igus Pages: 15

Brand: Samsung Pages: 11

Brand: Samsung Pages: 14

Brand: Samsung Pages: 14

Brand: Samsung Pages: 17

Brand: Samsung Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands