Lucent Technologies PacketStar PSAX 45N74 User Manual Download Page 43 | Manualshive

Page: 43 / 104

background image

255-700-585

3-7

PacketStar

®

PSAX 3-Port DS3/E3 ATM Protection Module User Guide

, Issue 1

Release 10.0.0

Chapter 3 Configuring Ports and Channels Using the Console

Configuring the Ports

Configuring the Ports

You must first configure the 3-Port DS3/E3 ATM Protection module before
you can set up connection provisioning. You can configure the module to
run in DS3 mode (see the next section, “Configuring the Ports in DS3
Mode”) or E3 mode (see the section ”Configuring the Ports in E3 Mode” on
page 3-20).

Table 3-2. Module Alarm Status Descriptions on the Equipment Configuration Window

Alarm Status

Module Type

Affected

Description

NoAlarm

I/O and Server Indicates that no alarms have been detected for the module

in this slot.

WrongCardType

I/O and Server Indicates that one type of module was configured in this

slot in the chassis, but a now different module occupies this
slot.

LineFailed

All

Indicates that the module in this slot is no longer receiving
or transmitting signals because the line failed.

Hexadecimal format,
Example:
12345678ABC

I/O and Server Indicates that one or more ports on the module in this slot

currently have a loss of signal. The numbers indicate which
ports have a loss of signal. For modules that have more
than eight ports not receiving signals, the value in this field
is in hexadecimal format.

CardRemoved

All

Indicates that one of the following events occurred:

•

The module in this slot was configured and then
removed from the slot.

•

Connections on the OC-3, OC-12, STM-1, or STM-4
APS/MSP primary module in this slot were transferred to
the standby module. After the transfer occurs, the former
primary module then displays

CardRemoved

in the

Alarm Status field; the former standby module then dis-
plays

Primary

in the Status field.

ReferenceClockFailed Stratum 3–4

Indicates that the timing reference clock on the Stratum
module in this slot failed.

CompositeClockFailed Stratum 3–4

Indicates that the timing composite clock on the Stratum
module in this slot failed.

Overload

Power Supply

Indicates that the Power Supply module is operating under
an overload condition.

PowerFailed

Power Supply

Indicates that the power has failed.

Minus48vFailed

Power Supply

Indicates that the -48 V dc Power Supply module output
failed.

UnknownAlarm

I/O and Server Indicates that the reason for failure is not known.

CompleteClockFailed

Stratum 3–4

Indicates that the backplane detected a clock error.

PowerFailed

Power Supply

Indicates that no power is coming into the PSAX chassis.

«
...
41
42
43
44
45
...
»

Summary of Contents for PacketStar PSAX 45N74









































































































Reviews:

No comments

Related manuals for PacketStar PSAX 45N74

615 Series ANSI

Brand: ABB Pages: 60

Brand: K&K Pages: 6

Brand: Ebyte Pages: 34

Brand: YASKAWA Pages: 61

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

Brand: FAAC Pages: 60

Brand: FAAC Pages: 12

Brand: FAAC Pages: 44

Brand: FAAC Pages: 44

Brand: FAAC Pages: 8

Brand: FAAC Pages: 60

Brand: FAAC Pages: 14

Brand: FAAC Pages: 68

Brand: FAAC Pages: 16

Brand: S&P Pages: 17

Brand: S&S Northern Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands