Lucent Technologies DACS II Features Manual Download Page 56

Page: 56 / 62

GL-2

Issue 2.0

April 2000

365-353-255

DACS II Operation and Maintenance Manual

Glossary

DACS

Digital Access and Cross-Connect System.

Default

A value the system automatically uses for a parameter if you do not specify a value.

Demultiplexer

A device used with a multiplexed signal for recovering signals contained within it and restoring the
distinct individual channels of these signals.

DS0

Digital Signal Level 0 (64-kb/s).

DS1

Digital Signal Level 1 (1.544-Mb/s).

DS1 Data Rate

The DS1 Data Rate is calculated as follows: DS1 = (24 Channels x 8 bit/ 1 frame bit) x 8000
samples/sec DS1 = 193 x 8000 = 1.544 Mb/s.

DS1 Port

A DS1 port in either a DS1 interface module or a DS3 interface module.

DS3

Digital Signal Level 3.

DS3U

DS3 Unit.

E1 Data Rate

The E1 Data Rate is calculated as follows:
E1 = (32 Channels x 8 bit/sample) x 8000 samples/sec
E1 = 256 x 8000 = 2.048 Mb/s

With this data rate, 30 channels carry traffic and two channels are reserved; one channel contains
framing information and the other channel contains signaling information.

Summary of Contents for DACS II






























































Search results

Summary of Contents for DACS II

Reviews:

Related manuals for DACS II

Brands by name

Popular brands

Lucent Technologies DACS II, Features Manual

Search results

Summary of Contents for DACS II

Reviews:

Related manuals for DACS II

Brands by name

Popular brands