background image

LUCAM B.V

 

 

Lucam b.v * Dukaat 19 * 8305BC * Emmeloord 

 

 

11 

 

11. Warranty 

The unit is covered by a factory warranty of 1 year after commissioning, but no later than 6 months after 
delivery of the unit. The warranty only covers material, but not the services. The warranty only covers if 
demonstrably completed maintenance has been carried out in accordance with our instructions and by a 
recognized installer.  
 
Warranty claims can only be exercised for defects in material and production errors. The device should not 
be disassembled by possible claim without our written permission.  
Spare parts warranty is only provided if supplied by us and have been installed by a recognized installer.  
 
Warranty extension is only granted in consultation and recorded in writing. If no maintenance has been 
performed on the installation the warranty becomes void.  

12. Liability 

The device is designed and manufactured as a ventilation system with the possibility of temperature change. 
The unit serves to ventilate by taking contaminated air outside the building and supplying fresh filtered air. 
Any other use is considered misuse and can lead to damage to the device or persons, Lucam b.v. cannot be 
held liable for this. 

Lucam b.v. accepts no liability for damage that can be traced back to: 

1.

 

Violations of the safety, operating and maintenance requirements of these technical documentation. 

2.

 

Use of materials not supplied by Lucam b.v. In such cases the responsibility solely by the installation 
company. 

3.

 

Normal wear. 

 

 

 

 

 

 

 

 

Summary of Contents for Fairtype 1200
















Reviews: