LSIS XP Series Troubleshooting Manual Download Page 46

4. Error Code List 

45

 

 

Object

 

Error code

 

Occurrence 

location

 

Error message

 

Reason and measure

 

Type

 

Address

 

Project 

download 

0x26 

0x1E 

XGT Panel 

Project data is not 
downloaded. Please 
download project 
again. 

The project data was not downloaded 
normally because of communication 
error. Check the connection status of 
communication cable and If this 
symptom is repeated, contact Customer 
Service Center.

 

0x1F 

XGT Panel/ 
XP-Builder 

Failed to read 
Version information 
file. Please 
download project 
again. 

There is version information file but when 
it can’t read file normally because of the 
device error, downloading is stopped 
because it doesn’t know version. If this 
symptom is repeated, contact Custom 
Service Center

 

Project 

download 

from 

USB storage 

device 

0x27 

0x51 

XGT Panel 

Cannot find project 
data in USB Storage 

There is no USB or device status of USB 
is not good or project is not saved 
properly.

 

0x52 

XGT Panel 

Project information 
file is not in USB 
Storage. 

The project is not saved normally in the 
USB. Check whether there is XP_Project 
folder and [project name].inf in the USB 
or not.

 

0x53 

XGT Panel 

Failed to read 
project information 
file. 

It can’t read project information file 
because the project is not saved in the 
USB normally. Save the project again 
from XP-Builder to the USB.

 

0x54 

XGT Panel 

Device type is not 
matched. 

The connected device type is not same 
as the device type set in the project in 
the USB. In case of this, project can’t be 
downloaded into the device. Edit the 
project again or download according to 
the connected device.

 

0x55 

XGT Panel 

Cannot read user 
password. 

Information about the password can’t be 
red because of the device error. If this 
symptom is

 

repeated, contact Customer 

Service Center.

 

0x56 

XGT Panel 

Password is not 
matched. 

When saving the project, the password 
inputted by user is not same as present 
connection password. Input correct 
password and save the project.

 

0x57 

XGT Panel 

Cannot read XGT 
Panel software 
version. 

There is version information file but when 
it can’t read file normally because of the 
device error, downloading is stopped 
because it doesn’t know version. If this 
symptom is repeated, contact Customer 
Service Center.

 

0x58 

XGT Panel 

XGT Panel software 
is old version. 
Please update XGT 
Panel. 

The version of XP-Builder where project 
is saved is not compatible with present 
XGT Panel. Update the XGT Panel.

 

0x58 

XGT Panel 

XP-Builder is old 
version. Please 
update XP-Builder. 

The version of XP-Builder where project 
is saved is not compatible with present 
XGT Panel. Update the XGT Panel.

 

Summary of Contents for XP Series




















































Reviews: