background image

43013-00 Rev. A, August 2009

Find a list of LSI Corporation’s U.S. distributors, international distributors, sales 
offices, and design resource centers on the LSI web site at:

http://www.lsi.com

LSI, the LSI logo design, and MyStorage are trademarks or registered trademarks 
of LSI Corporation. All other brand and product names may be trademarks of their 
respective companies.

Copyright © 2009 by LSI Corporation. All rights reserved.

LSI Corporation reserves the right to make changes to any products and services 
herein at any time without notice. LSI does not assume any responsibility or liability 
arising out of the application or use of any product or service described herein, 
except as expressly agreed to in writing by LSI; nor does the purchase, lease, or 
use of a product or service from LSI convey a license under any patent rights, 
copyrights, trademark rights, or any other of the intellectual property rights of LSI 
or of third parties. 

RAID 1 (drive mirroring):

 Data is written simultaneously 

to both drives in the drive group, providing complete data 
redundancy if one drive fails. RAID 1 supports an even 
number of drives from 2 to 32 in a single span.

RAID 5 (drive striping with distributed parity):

 Data is 

striped across all drives in the group. Part of the capacity 
of each drive stores parity information that reconstructs 
data if a drive fails. RAID 5 provides good data throughput 
for applications with high read request rates.

RAID 10 (RAID 1 and RAID 0 in spanned groups):

 

RAID 10 uses mirrored pairs of drives to provide complete 
data redundancy. RAID 10 provides high data throughput 
rates.

Note:

Refer to the 

MegaRAID SAS Software User’s 

Guide

 on the 

MegaRAID Universal Software 

Suite

 CD for more information about RAID levels.

T E C H N I C A L   S U P P O R T

For assistance in installing, configuring, or running the SAS 
9240-4i RAID controller or the SAS 9240-8i RAID controller, 
contact an LSI Technical Support representative.

Click the following link to access the LSI Technical Support 
page for storage and board support: 

http://www.lsi.com/support/storage/tech_support/index.html

From this page, you can send an email or call Technical 
Support, or submit a new service request and view its status.

E-mail:

 

http://www.lsi.com/support/support_form.html

Phone Support: 

http://www.lsi.com/support/storage/phone_tech_support/
index.html

1-800-633-4545 (North America)

00-800-5745-6442 (International

Note:

The international toll-free number does not 
require country-specific access codes.

Summary of Contents for MegaRAID SAS 9240-4i

Page 1: ... Note SATA II is the only type of SATA supported by these RAID controllers R A I D C O N T R O L L E R I N S TA L L AT I O N Step 1 Unpack the RAID Controller Unpack the RAID controller in a static free environment Remove it from the antistatic bag and inspect it for damage If the RAID controller appears to be damaged or if the MegaRAID Universal Software Suite CD is missing contact LSI or your Me...

Page 2: ...and the bottom of the board TP1 Universal Asyn chronous Receiver Transmitter UART debugging 4 pin connector Reserved for LSI use U2 MegaRAID Skinny 1 wire connector 2 pin connector To create a RAID 5 configuration you have to plug a 1 wire key into this connector Refer to the MegaRAID 6Gb s SAS RAID Controllers User s Guide for more information Jumper Connector Type Description J1 RISCwatch header...

Page 3: ... it is turned on to the devices the computer might not recognize the devices The firmware takes several seconds to initialize During this time the controller scans the ports Step 8 Run the WebBIOS Configuration Utility Run the WebBIOS Configuration Utility to configure the groups and the virtual drives When the message Press Ctrl H for WebBIOS appears on the screen immediately press CTRL H to run ...

Page 4: ... single span RAID 5 drive striping with distributed parity Data is striped across all drives in the group Part of the capacity of each drive stores parity information that reconstructs data if a drive fails RAID 5 provides good data throughput for applications with high read request rates RAID 10 RAID 1 and RAID 0 in spanned groups RAID 10 uses mirrored pairs of drives to provide complete data red...

Reviews: