LSI LSI53C1000 Technical Manual Download Page 17 | Manualshive

Page: 17 / 384

background image

LSI53C1000 PCI to Ultra160 SCSI Controller

1-1

Chapter 1
Introduction

This chapter provides a general overview on the LSI53C1000 PCI to
Ultra160 SCSI Controller. This chapter contains the following sections:

•

Section 1.1, “General Description”

•

Section 1.2, “Benefits of Ultra160 SCSI”

•

Section 1.3, “Benefits of SureLINK (Ultra160 SCSI Domain
Validation)”

•

Section 1.4, “Benefits of LVDlink”

•

Section 1.5, “Benefits of TolerANT

•

Section 1.6, “Summary of LSI53C1000 Benefits”

1.1 General Description

The LSI53C1000 brings Ultra160 SCSI performance to host adapter,
workstation, and server designs, making it easy to add a
high-performance SCSI bus to any PCI system.

The LSI53C1000 supports a 64-bit or 32-bit, 66 or 33 MHz PCI bus. The
Ultra160 SCSI features implemented in the LSI53C1000 are: Double
Transition (DT) clocking, Cyclic Redundancy Check (CRC), and Domain
Validation. These features comply with the Ultra160 SCSI industry
initiative.

DT clocking permits the LSI53C1000 to transfer data up to
160 megabytes per second (Mbytes/s). CRC improves the integrity of the
SCSI data transmission through enhanced detection of communication
errors. Asynchronous Information Protection (AIP) augments CRC to
protect all nondata phases, providing complete end-to-end protection of
the SCSI I/O. SureLINK™ Domain Validation detects the SCSI bus

«
...
15
16
17
18
19
...
»

Summary of Contents for LSI53C1000

































































































































































































































































































































































































Reviews:

No comments

Related manuals for LSI53C1000

Brand: ABB Pages: 30

Brand: ABB Pages: 15

Brand: ABB Pages: 10

Brand: ABB Pages: 44

Brand: Galcon Pages: 32

Brand: U.S. Divers Pages: 22

Brand: Vaillant Pages: 52

Brand: Vaillant Pages: 11

Pulsafeeder MPC Vector

Brand: Idex Pages: 114

Brand: Measurement Computing Pages: 32

CIATControl OPC Server

Brand: CIAT Pages: 32

Brand: Danfoss Pages: 8

Infi 90 IMAOM01

Brand: Bailey Pages: 44

E4KP ENTRYCHECK

Brand: SDC Pages: 6

Brand: Ashly Pages: 1

Brand: OneFex Pages: 24

Brand: Lampert Pages: 15

Brand: MERCATOR Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands