Lowrance StructureScan Installation Manual Download Page 12

Page: 12 / 12

*988-0179-01A*

Navico Holding AS

StructureScan LSS-1 Module (000-00099-002)

LSS-1 mounting screws (4)

Closed-end crimp connector

Fuse and fuse holder

StructureScan Trolling Motor Bracket (000-00099-004)

Trolling motor bracket hose clamps (2)

Zip ties (4)

No. 8 transducer attachment screws (6)

StructureScan Skimmer Bracket (000-00099-005)

Transom mount screws (2)

Bracket assembly nuts (2)

Transducer attachment lock nuts (6) Transducer attachment screws (6)
Bracket assembly bolts (2)

Zip ties (2)

Bracket assembly washers (4)

StructureScan Skimmer Transducer (000-00099-007)

Transom mount screws (2)

Bracket assembly nuts (2)

Transducer attachment lock nuts (6) Transducer attachment screws (6)
Bracket assembly bolts (2)

Zip ties (2)

Bracket assembly washers (4)

Visit our website:

www.lowrance.com

Summary of Contents for StructureScan













Search results

Summary of Contents for StructureScan

Reviews:

Related manuals for StructureScan

Brands by name

Popular brands

Lowrance StructureScan, Installation Manual

Search results

Summary of Contents for StructureScan

Reviews:

Related manuals for StructureScan

Brands by name

Popular brands