background image

Preface

 Warning: 

It is your sole responsibility to install and

use the instrument and transducer(s) in a manner that
will not cause accidents, personal injury or property
damage. Always observe safe boating practices.

Sonar performance: 

The accuracy of the sonar depth display can

be affected by many factors, including the type and location of the
transducer and water conditions. Never use this instrument to
gauge depth or other conditions for swimming or diving.
The choice, location, and installation of transducers and other
components of the system are critical to the performance of the
system as intended. If in doubt, consult your Navico dealer.
To reduce the risk of misusing or misinterpreting this instrument,
you must read and understand all aspects of the Installation and
Operation manuals. We also recommend that you practice all
operations using the built-in simulator before using this instrument
on the water.

Disclaimer:

 Navico Holding AS and its subsidiaries, branches and

affiliates disclaim all liability for any use of this product in a way that
may cause accidents, damage or that may violate the law.

Compliance Statements:

 The StructureScan 3D Transducer

complies with:

CE under EMC directive 2014/30/EU

The requirements of level 2 devices of the Radiocommunications
(Electromagnetic Compatibility) standard 2008

The relevant Declaration of Conformity is available at the following
websites under the StructureScan 3D Transducer documentation
section:

http://www.lowrance.com/

http://www.simrad-yachting.com/

Trademarks:

 Lowrance

®

 and Navico

®

 are registered trademarks of

Navico. Simrad

®

 is used by license from Kongsberg.

This manual refers to the following Navico products: DownScan
Imaging™ (DownScan), DownScan Overlay™ (DownScan Overlay),

2

Preface

 | StructureScan 3D Transducer

Summary of Contents for StructureScan 3D





















Reviews:

Related manuals for StructureScan 3D