Lowell MA30 Installation Sheet And Operators Manual Download Page 2

2

REMOVABLE

PHOENI X

CONNECTOR

Instruction Sheet

IS-MA30

Issued: 2-18-19

Lowell Manufacturing Company

100 Integram Drive

Pacific, Missouri 63069 U.S.A.

Call: 800-325-9660

Fax: 636-257-6606

Click: www.lowellmfg.com

 

Read these instructions.    

Keep these instructions.    

Heed all warnings.  

Follow all instructions.       

Do not use this apparatus near water.    

Clean only with a dry cloth. 
Do not block any ventilation openings.  Install in accordance with manufacturer

s instructions. 

Do not install near any heat sources such as radiators, registers, stoves, or other apparatus (including amplifiers) 

that produce heat. 

Do not defeat the safety purpose of the polarized or grounding-type plug.  A polarized plug has two blades with 

one wider than the other.  A grounding-type plug has two blades and a third grounding prong.  The wide blade or 
third prong is provided for your safety.  If the provided plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet. 

Protect the power cord and plug from being walked on or pinched particularly at plugs , convenience receptacles, 

and the point where it exits from the apparatus. 

Only use attachments and accessories specified by the manufacturer . 
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. 

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 

Unplug this apparatus during lightning storms or when unused for long periods of time . 
Refer all servicing to qualified service personnel .  Servicing is required when the apparatus has been damaged in 

any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the 
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 

The plug on the power cord is the AC mains disconnect device and must remain readily operable .  To completely 

disconnect this apparatus from the AC mains, disconnect the power supply cord plug from the AC receptacle. 

This apparatus shall be connected to a mains socket outlet with a protective earthing connection . 
When permanently connected, an all-pole mains switch with a contact separation of at least 3 mm in each pole 

shall be incorporated in the electrical installation of the building. 

If rack mounting, provide adequate ventilation.  Equipment may be located above or below this apparatus, but 

some equipment (like large power amplifiers) may cause an unacceptable amount of hum or may generate too 
much heat and degrade the performance of this apparatus. 

This apparatus may be installed in an industry standard equipment rack .  Use screws through all mounting holes 

to provide the best support. 

WARNING: 

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.  Apparatus 

shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the 
apparatus.  This product may contain chemicals known to the State of California to cause cancer , or birth defects or 
other reproductive harm. 

NOTE: This equipment may generate, uses, and can radiate radio frequency energy and, if not installed and used in accordance 
with the instructions, may cause harmful interference to radio communications .  However, there is no guarantee that interference 
will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more 
of the following measures:  Reorient or relocate the receiving antenna. 
Increase the separation between the equipment and receiver. 
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
Consult the dealer or an experienced radio/TV technician for help. 

 

CAUTION:

 Changes or modifications not expressly approved by Lowell Manufacturing will void the manufacturers warranty .  

IMPORTANT SAFETY INSTRUCTIONS

Summary of Contents for MA30









Reviews: