background image

As  always,  If  you  experience any  difficulty during the  installation  of  this  product 
please    contact  Low  Range  Off-Road  Technical  Support  at  801-805-6644  M-F 
7:30am-5:30pm MST.  Thank you for purchasing from Low Range Off-Road.

These  instructions  are  designed  as  a  general  installation guide. Installation of many Low  Range 
Off-Road  products  require specialized  skills  such as  metal fabrication,  welding  and  mechanical 
trouble  shooting. If you  have any questions  or are unsure about  how  to proceed,  please contact 
our shop at  801-805-6644 or seek help from a competent fabricator. Using fabrication tools  such 
as  welders,  torches  and  grinders  can  cause  serious  bodily  harm  and  death.  Please  operate 
equipment carefully and observe proper safety procedures.

Rock crawling and  off-road  driving  are inherently dangerous activities. Some modifications  will 
adversely affect  the  on-road  handling  characteristics  of your vehicle. All  products  sold  by  Low 
Range Off-Road  are sold  for off road  use only. Any other use or application is the responsibility 
of the purchaser and/or user. Some modifications and installation of certain aftermarket parts may 
under certain circumstances void your original dealer warranty. Modification of your vehicle may 
create  dangerous  conditions, which  could  cause  roll-overs  resulting  in serious  bodily injury  or 
death. Buyers and  users  of these products hereby expressly assume all risks associated  with any 
such modifications and use.

Revised 02/21/14

©     Copyright 2014 Low Range Off-Road, LC

      

 All Rights Reserved

Summary of Contents for SER-CHK





















Reviews: