Lovol KM/4L22 Maintenance Manual Download Page 115

Page: 115 / 155

MAINTENANCE MANUAL OF ENGINE

109

2. Inspecting engine oil level

Inspection conditions:

◆

The machine is stopped at a level ground.

◆

The shift lever is at neutral position.

◆

The ignition lock is off.

◆

The parking brake is pulled tightly.

◆

Five minutes after the engine stops.

Inspection steps:

◆

Clean surrounding of the oil dipstick.

◆

Remove the oil dipstick, and wipe it clean with a

test paper.

◆

Install the oil dipstick, and ensure it is installed at

place.

◆

Remove the oil dipstick, and inspect whether the

oil level meets the requirements.

Normal conditions:

◆

The oil level is not too low.

◆

The engine oil is not too thick, thin or rare.

◆

No diesel smell exists.

◆

The oil is free from obvious metal objects, inclu-

sions, or deterioration.

Abnormal conditions:

◆

Replenish oil to the level set forth in the specifi-

cation according to the oil dipstick marking.

◆

Change the contaminated oil and oil filter.

◆

Consult the engine operation manual for details.

Upper scale line

Lower scale line

Summary of Contents for KM/4L22




























































































































































Search results

Summary of Contents for KM/4L22

Reviews:

Related manuals for KM/4L22

Brands by name

Popular brands

Lovol KM/4L22, Maintenance Manual

Search results

Summary of Contents for KM/4L22

Reviews:

Related manuals for KM/4L22

Brands by name

Popular brands