background image

Portable 15 Channel Remote Unit

1-15 (O operates all blinds) 

2 jogs = 1 movement, up AND down

STEP 1 - PAIRING THE HANDSET WITH THE MOTOR
NOTE: During the setting procedure, the time between two 

operations must not exceed 10 seconds as this will cause the setting up 

process to quit.

2 jogs = 1 movement, up AND down.
• 

Switch on the power to the motor

• 

Remove the battery cover on the reverse of the remote. There are 

two setting buttons (P2) on either side of the battery, press either 

one

• 

Select a channel from 1- 15 on the remote by pressing 

Channel < or >

• 

Press the button on the motor and the motor will jog up and 

down 

• 

Press P2 twice then the Up or Down button once. The motor 

will jog and beep

The motor and remote are now paired.
• 

Check direction

• 

To change direction press and hold the button on the motor for 

4 jogs

• 

Move to a midway position 

STEP 2 - SETTING THE LIMITS
Select the same channel and set the limits.
• 

You can select either position first

• 

Press P2, then the Up button followed by P2 again, the motor 

will jog and beep 

• 

Press the Up button and the blind will start to rise

• 

Press P2 when the blind is close to the top and the blind will go into 

slow jog mode

• 

If you do not get the correct position press down and repeat by going 

up

• 

Press the Stop button on the remote and the blind will stop

• 

Hold the Stop button down until the motor jogs twice, this will

           set the top limit
• 

Press the Down button and the blind will start to go down

• 

Press P2 and the blind will go into slow jog mode

• 

Press the Stop button on the remote and the blind will stop

Press and hold the stop button down until the motor jogs, this 

will set the lower limit.
Setting is complete. For more blinds, select another channel on the 

remote and repeat from Step 2.

Down button

Channel <

Stop Button

Up Button

LCD
Screen

Channel >

Setting Button

STEP 3 - SETTING A THIRD POSITION

• 

Move the blind using the Up and Down buttons on the remote to the desired position (press Stop)

• 

Press Stop followed by the P2 button then Stop twice more, this will cause the motor to jog twice

• 

To operate the third position, press and hold the Stop button and the blind will move to its third position

• 

To delete the third position, press P2, followed by the Stop button twice, the motor will jog twice

DELETING A  LIMIT 

• 

To delete a limit, press P2 followed by the Down button then press P2 again, the motor will jog twice

DELETING A  HANDSET

• 

To delete a handset, press P2 then the Stop button followed by P2 again, the motor will jog twice

ADDING A  HANDSET

• 

To add a handset, press P2 twice on the existing handset. Then press P2 once on the new handset, the motor will jog twice

• 

To perform a factory reset press and hold the button on the motor for 6 jogs

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN 
INCORRECT TYPE. DISPOSE OF USED BATTERIES 
ACCORDING TO THE INSTRUCTIONS. 

 

Technical specification

Input voltage: 3V (CR2450) X 1
Transmitting frequency: 433MHz
Transmitting power: 10 milliwatt
Operating temperature: -10

0

c to 50

0

c

Transmission distance: 200 metres open office, 35 metres on two walls

R 1 7 3 0   R E M O T E   C O N T R O L

for use with R1725

Notice: Do not expose the unit to moisture or heat. When
you use the control unit, if operation distance becomes 
short and less effective then please replace batteries. 
Please recycle old batteries.

R 1 7 3 5   R E M O T E   C O N T R O L

Summary of Contents for R1725

Page 1: ...t L1 Rolling L2 Rolling L1 Open L2 Partition Emission frequency 100V 240V 200m 35m 433 92 868 MHz Insert motor into the roller tube INSTALLATION Manufacture the blind according to instructions and fit using brackets supplied DRIVE ADAPTER INSTALLATION Place crown Motorplate Slide the crown up the tube to the control end Drive Crown Drive Screw the drive to the opposite end and fit Circlip 1 2 3 Bl...

Page 2: ...p Press and hold the stop button down until the motor jogs this will set the lower limit Setting is complete For more blinds select another channel on the remote and repeat from Step 2 Down button Channel Stop Button Up Button LCD Screen Channel Setting Button STEP 3 SETTING A THIRD POSITION Move the blind using the Up and Down buttons on the remote to the desired position press Stop Press Stop fo...

Page 3: ...he remote and repeat step 2 Down Button Channel Setting Button Channel Setting Button Stop Button Up Button STEP 3 SETTING A THIRD POSITION Move the blind using the Up and Down buttons the remote to the desired position press Stop Then O and together followed by the Stop button twice more this will cause the motor to do 2 jogs and beep To operate the third position press and hold the Stop button a...

Page 4: ...wered on 14 Do not operate the blinds during maintenance such as window cleaning is being carried out in the vicinity etc 15 The power supply cord should not be exposed to sunlight or rain directly during installation H05VV of the motor power supply cord can only be used for indoor installations H05RR or H05RN rubber power cable can be used in outdoor installation black ordinary tough rubber sheat...

Reviews: