background image

 

 

v

 

ARC RAYS can burn 

Ø

 

  Avoid  eye  and  body  damage.  Arc  rays  and  infrared  radiation  can  cause 

injury  to  the  eyes  and  burn  the  skin.  Wear  ANSI  approved  eye  and  body 
protection.  Do  not  allow  viewing  by  visitors  without  proper  eye  and  body 
protection.   

Ø

 

Use  a  shield  with  the  proper  filter  and  cover  plates  to  protect  your  eyes 

from sparks and the rays of the arc when plasma cutting or observing open arc plasma cutting. 

Ø

 

Use suitable clothing made from durable flame-resistant material to protect your skin and that of 
your helpers from the arc rays.   

Ø

 

Protect  other  nearby  personnel  with  suitable,  non-flammable  screening  and/or  warn  them  not  to 
watch the arc nor expose themselves to the arc rays or to hot spatter or metal. 

 

v

 

WELDING SPARKS can cause fire or explosion   

Ø

 

Remove fire hazards from the cutting area. If this is not possible, cover 

them  to  prevent  the  welding  sparks  from  starting  a  fire.  Remember  that  welding 
sparks  and  hot  materials  from  cutting  can  easily  go  through  small  cracks  and 
openings  to  adjacent  areas.  Avoid  cutting  near  hydraulic  lines.  Have  a  fire 
extinguisher readily available. Do not operate the electric arc welder in areas where 
flammable or explosive vapors are present. 

Ø

 

Where compressed gases are to be used at the job site, special precautions should be used to 
prevent hazardous situations.   

Ø

 

Do not heat, cut or weld tanks, drums or containers until the proper steps have been taken to 
insure that such procedures will not cause flammable or toxic vapors from substances inside. 
They can cause an explosion even though they have been “cleaned”.   

Ø

 

Always keep a fire extinguisher nearby while welding.   

Ø

 

Use welding blankets to protect painted surfaces, dashboards, engines, etc. 

Ø

 

Please make sure there are no combustible items around your welding area.   

v

 

CYLINDER may explode if damaged   

Ø

 

Use only compressed gas cylinders containing the correct shielding gas for the 

process  used  and  properly  operating  regulators  designed  for  the  gas  and  pressure 
used. All hoses, fittings, etc. should be suitable for the application and maintained 
in good condition.   

Ø

 

Always  keep  cylinders  in  an  upright  position  securely  chained  to  an 

undercarriage or fixed support.   

Ø

 

Cylinders should be located:   

ž

 

Away from areas where they may be struck or subjected to physical damage.   

ž

 

A safe distance from arc welding or cutting operations and any other source of heat, sparks, 
or flame.   

Ø

 

Never allow any electrically “hot” parts to touch a cylinder.   

Ø

 

Keep  your  head  and  face  away  from  the  cylinder  valve  outlet  when  opening  the  cylinder 
valve.   

Ø

 

Valve protection caps should always be in place and hand tight except when the cylinder is in 
use or connected for use.   

Summary of Contents for MIG175






















Reviews: