background image

TO MEASURE  

BREAKING STRENGTH:

When a loop or splice is properly swaged, 

Locoloc

®

 copper and aluminum oval sleeves 

are capable of supporting a greater load than 

the rated breaking strength of the flexable 

construction metal cable to which they are 

attached. Locoloc® stop sleeves are capable 

of holding only 1/3 to 1/2 of the rated breaking 

strength of the cable.ratedratebreaking 

strength of the cable to which they are 

attached. 

CAUTION:

Always use a five to one safety factor 

when designing cable assemblies.

If the strength of the cable is 2,000 lbs. 

(1/8" 7X19 galvanized aircraft cable) then 

the maximum load to which the cable 

or the assembly is subject should never 

exceed 400 lbs. When an oval sleeve or 

other fitting capable of holding the rated 

breaking strength of the cable is used as a 

termination.  When a stop sleeve is used this 

safety factor should be increased to 10 to 1.

TABLE A      

Suggested starting gauge pressure

Sleeve size 

Description 

 

 

Pressure*(Gauge) 

Dies 

 

3/64 

 

Copper oval and stop sleeves 

   200 lbs. 

 

3/64 Dies

1/16 

 

Copper oval and stop sleeves 

   250 lbs. 

 

1/16 Dies

3/32 

 

Aluminum oval and stop sleeves 

   300 lbs. 

 

3/32 Dies

3/32 

 

Copper oval and stop sleeves 

   450 lbs. 

 

3/32 Dies

1/8 

 

Aluminum oval and stop sleeves 

2,000 lbs. 

 

  1/8 Dies

1/8 

 

Copper oval and stop sleeves 

2,500 lbs. 

 

  1/8 Dies

5/32 

 

Aluminum oval sleeves 

 

2,700 lbs. 

 

5/32 Dies

5/32 

 

Aluminum stop sleeves 

 

2,700 lbs. 

 

 1/8 Dies

5/32 

 

Copper oval sleeves 

 

3,000 lbs. 

 

5/32 Dies

5/32 

 

Copper stop sleeves 

 

3,000 lbs. 

 

  1/8 Dies

3/16 

 

Aluminum oval sleeves 

 

4,000 lbs. 

 

3/16 Dies

3/16 

 

Aluminum stop sleeves 

 

4,000 lbs. 

 

  1/8 Dies

3/16 

 

Copper oval sleeves 

 

4,500 lbs. 

 

3/16 Dies

3/16 

 

Copper stop sleeves 

 

4,500 lbs. 

 

  1/8 Dies

7/32 

 

Aluminum oval sleeves 

 

5,000 lbs. 

 

7/32 Dies

7/32 

 

Aluminum stop sleeves 

 

5,000 lbs. 

 

  1/8 Dies

7/32 

 

Copper oval sleeves 

 

5,000 lbs. 

 

7/32 Dies

7/32 

 

Copper stop sleeves 

 

5,000 lbs. 

 

  1/8 Dies

1/4 

 

Aluminum oval and stop sleeves 

5,000 lbs. 

 

  1/4 Dies

1/4 

 

Copper oval and stop sleeves 

5,500 lbs. 

 

  1/4 Dies

9/32 

 

Aluminum oval sleeve 

 

5,500 lbs. 

 

9/32 Dies

9/32 

 

Copper oval sleeves 

 

5,500 lbs. 

 

9/32 Dies

9/32 

 

Copper oval stop sleeves   

5,500 lbs. 

 

  1/4 Dies

5/16 

 

Aluminum oval sleeve 

 

5,500 lbs. 

 

5/16 Dies

5/16 

 

Copper oval sleeves 

 

5,800 lbs. 

 

5/16 Dies

5/16 

 

Copper stop sleeves 

 

5,800 lbs. 

 

  1/4 Dies

3/8 

 

Aluminum oval sleeve 

 

6,000 lbs. 

 

  3/8 Dies

3/8 

 

Copper oval sleeves 

 

6,500 lbs. 

 

  3/8 Dies

3/8 

 

Copper stop sleeves 

 

6,500 lbs. 

 

  1/4 Dies

7/16 

 

Aluminum oval sleeve 

 

6,500 lbs. 

 

7/16 Dies

7/16 

 

Copper oval sleeve 

 

6,500 lbs. 

 

7/16 Dies

1/2 

 

Aluminum oval sleeve 

 

6,500 lbs. 

 

  1/2 Dies

1/2 

 

Copper oval sleeve 

 

6,500 lbs. 

 

  1/2 Dies

 

* 5/16, 7/16, 1/2 and 3/8” sleeves require two compressions. 

Each compression will swage 1/2 the length of the sleeve.

www.loosnaples.com

Toll Free: 800-321-LOOS (5667)

4

Summary of Contents for LOCOLOC 5-H









Reviews: