Loopcomm LP-8096 User Manual Download Page 10

Page: 10 / 66

LED Indicators

Power:

Indicates when the Dual Band Wireless Router is powered on. The

LED will remain on.

5.0GHz Wireless Activity:

Blinks rapidly when wireless data traffic is

transmitted or received over the 5.0GHz wireless network.

2.4GHz Wireless Activity:

Blinks rapidly when wireless data traffic is

transmitted or received over the2.4GHz wireless network.

WPS:

Wi-Fi Protected Setup activity. When the WPS mode is

activated the

WPS LED blinks as it awaits a connection.

USB Connection:

Indicates when a USB storage device is connected to the

USB port for local sharing.

Gigabit Wired Ports 1-4:

Indicates when a networking device is connected to

a wired port on the back of the Dual Band Wireless Router. The LED blinks

rapidly when wired data traffic is transmitted or received.

Internet Connection:

Indicates when the Dual Band Wireless Router is

connected to a broadband modem. The LED will blink when Internet traffic is

transmitted or received.

Summary of Contents for LP-8096































































Search results

Summary of Contents for LP-8096

Reviews:

Loopcomm LP-8096, User Manual, Page: 10 / 66

Search results

Summary of Contents for LP-8096

Reviews: