Loopcomm LP-2596K User Manual Download Page 91 | Manualshive

Page: 91 / 91

background image

91

5.Compliance

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against  harmful  interference  in  a  residential  installation.  This  equipment  generates,  uses,  and
can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the
instructions,  may  cause  harmful  interference  to  radio  communications.  However,  there  is  no
guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

RF Radiation Exposure and Hazard Statement:

To ensure compliance with FCC RF exposure requirements, this device must be installed in a
location such that the antenna of the device will be greater than 0.6 m away from all persons.
Using higher gain antennas and types of antennas not covered under the FCC certification of
this product is not allowed. Installers of the radio and end users of the product must adhere to
the installation instructions provided in this manual. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.

Non-modification Statement:

Use only the integral antenna supplied by the manufacturer when operating this device.
Unauthorized antennas, modifications, or attachments could damage the TI Navigator access
point and violate FCC regulations. Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this equipment.

Copyright © 2014 Loopcomm Technology Inc. All rights reserved.

«
...
89
90
91

Summary of Contents for LP-2596K




























































































Reviews:

No comments

Related manuals for LP-2596K

Brand: Ocens Pages: 2

Brand: Gemtek Pages: 35

Brand: Systimax Pages: 197

Brand: Planet Pages: 42

Brand: wattsonic Pages: 60

Brand: Ubiquiti Pages: 24

Brand: ZyXEL Communications Pages: 2

Brand: TP-Link Pages: 2

Brand: Linksys Pages: 19

Brand: ZyXEL Communications Pages: 164

Brand: PHICOMM Pages: 58

Brand: Advantek Networks Pages: 62

WatchDog 3388BC

Brand: Spectrum Technologies Pages: 10

Brand: Air Live Pages: 102

Brand: Zadako Pages: 30

Cerberus [P 6367]

Brand: Pentagram Pages: 48

Brand: H3C Pages: 29

Brand: Intellinet Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands