manualshive.com logo in svg

LONCIN WG6500M-1, Owner'S Manual

Share
Download
LONCIN WG6500M-1 Owner'S Manual Download Page 17

Operation and use of the set 

- 13 - 

V. Operation and use of the set 
1) Starting the engine 

①

 Remove all loads from the output end. 

②

 Open fuel switch 

③

 Put AC circuit breaker in the OFF position. 

④

 Put throttle lever in the OFF position.

 

Do not shut off the choke if the engine is started when it is warm. 

 

⑤

 Put the engine switch in the ON position. 

⑥

 Gently pull up the starter grip and pull it out briskly when a resistance is felt. 

⑦

 When the engine has warmed up, put choke lever in the ON position. 

2) Use of the generator 

①

 Connecting to home power supply 

If the generator is to be connected to a home power supply as a standby, 

connection shall be performed by a professional electrician or by another person with 
proficient electrical skill. 
 
When the loads are connected to the generator, please carefully check whether 
electrical connections are safe and reliable. Any improper connection may cause 
damage to the generator, or a fire. 
 
 

 

 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Good 

Prohibited 

Good 

Summary of Contents for WG6500M-1
































Reviews:

No comments

Brands by name

Popular brands

Load more brands