Logitech Electronics 200 MKII Series User Manual Download Page 14 | Manualshive

Page: 14 / 14

Logitech Electronics 200 MKII Series User Manual Download Page 14

Low Voltage Directive

It is essential that the mains supply to the instrument is fused externally to no more than 1A and that
the cabling supplying power to the instrument is rated for at least 3A.

Low voltage signal cables should not be run in the same conduit or twisted or tied to cables carrying
voltages in excess of 50V (AC or DC).

If the instrument is not installed fully in accordance with the instructions in this User Guide it may not
comply with the requirements of the Low Voltage Directive.

Warranty

200C

MKII

SERIES

™

Counters carry a two year warranty that is only valid where there is no damage

caused by accident, negligence, misapplication, or repairs/modifications attempted by unauthorised
personnel. The warranty only extends to the original user.

Copyright ©

Logitech Electronics Limited

1994 to 2017

Document No: 200C-

MKII

_hb v3.0 August 2017

200C-

MKII

_hb v3.1 01/2020

!

14

Design and Manufacture of Electronic Systems and Instrumentation. Supply of Sensors and Transducers

Lane End | Church Aston | Newport | Shropshire | TF10 9JJ | UK

www.logitechelectronics.com

t: +44 (0)1952 820444

e: [email protected]

MADE IN THE UK

«
...
12
13
14

Summary of Contents for 200 MKII Series















Reviews:

No comments